Operating Instructions
309047
Rev. A
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
Pressure Roller
Model 243066, Series A
D 20 in. (50 cm) heavy-duty extension
D 45_ swivel adapter
D 9 in. (23 cm) roller frame
D 1/2 in. (13 mm) nap roller cover
3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure
*
This maximum pressure is only possible if the roller frame is
completely plugged. The best operating pressure is the lowest
pressure that provides an even paint supply to the roller and
typically does not exceed 300 psi (2.1 MPa, 21 bar).
*
9593A
Airless spray
gun not included
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 2000, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
Flushing
This is the procedure for flushing the pressure roller.
The pump and gun you are using may have additional
flushing steps, such as cleaning filters and screens.
See the pump and gun flushing instructions.
Parts Drawing
Pressure Roller,
Model 243066, Series A
NOTE: Leave the pressure roller attached to the gun
for this procedure.
diffuser
retaining nut
6
See Pressure Relief
Procedure on page 2.
1
2
1. Relieve the pressure.
2. Remove roller cover (6) and diffuser from roller
frame as follows (see Parts Drawing at right):
3
a. Hold roller cover, and unscrew retaining nut.
b. Slide diffuser and roller cover off of roller fame.
c. Pull roller cover off of diffuser.
3. Clean roller cover with compatible fluid, and clean
diffuser by shaking vigorously in pail of compatible
fluid to remove wet paint. Use soft bristled brush to
remove any dried paint on diffuser.
4
5
4. Place roller frame (1) in empty waste pail.
5. Prime pump with flushing fluid compatible with
paint you are using, and use the lowest pressure
setting at which pump primes.
6. Put pump prime/drain valve in position that
delivers fluid to hose.
NOTE: Perform Step 7 at the lowest pressure
possible.
2
3
7
7. Trigger gun until flushing fluid coming out of roller
2*
3*
frame is relatively clear.
9593A
8. Shut off the pump, and relieve the pressure.
HINT:
9. To prevent corrosion, lubricate paint holes in roller
frame with lightweight oil that does not contain
silicone.
When replacing gasket (2*) and
o-ring (3*) in swivel adapter (7),
position o-ring first, then press
gasket into place.
Storage
If you are going to store the airless equipment for an
extended period of time after flushing with water-base
fluid, flush again with Graco Pump Armor or mineral
spirits/paint thinner. Leave the fluid in the system
during storage.
Parts List
Ref.
No.
Part No. Description
Qty.
1
2
3
4
240005
162863
114049
232122
195804
107590
FRAME, roller; 9 in. (23 cm)
GASKET, non-metallic
PACKING, o-ring
TUBE, extension; 20 in. (50 cm)
LABEL, warning
1
3
3
1
1
Additional Roller Covers
The following pressure roller covers are available at
your local distributor:
5Y
6
COVER, roller;
107589
107590
107591
107592
9 in. (23 cm); 3/8 in. (9.5 mm) nap
9 in. (23 cm); 1/2 in. (13 mm) nap
9 in. (23 cm); 3/4 in. (19 mm) nap
9 in. (23 cm); 1-1/4 in. (32 mm) nap
9 in. (23 cm); 1/2 in. (13 mm) nap 1
7
224399
ADAPTER, 45_ swivel
1
Y Call 1–800–328–0211 for free extras.
309047
3
Graco Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in
accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty
Program”.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–690–2894 Toll Free
All written and visual data contained in this document reflect the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit
Foreign Offices: Belgium, Korea, Hong Kong, Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN USA 309047 02/2000
4
309047
|