Domestic Dishwasher
DW12-BFE ME
GB
Code:0120503412
Close-up View (Interrior)
Bottom Spray Arm
Washing Filter
Upper Rack
E
F
G
H
I
A
Rack Height Adjustor
B
Detergent and Rinse Aid Dispenser
Salt Container Cap
Third Sprayer
Top Spray Arm
C
Lower Rack
D
Technical characteristics
60cm
Width
60cm
85cm
Depth
Height
12 standard place settings
Capacity
0.03-0.6MPa
Mains water pressure
Power voltage
Total absorber power
220-240V~ 50Hz
2150W
.2.
GB
S a l t ꢀꢀ
Salt
Adjusting Salt Consumption
The hardness of the water varies from place to place. If hard
water is used in the dishwasher,deposits will form on the dishes
utensils.
The dishwasher is designed to allow for adjusting the amount of
salt consumed based on the hardness of the water used.This is
intened to optimize and customize the level of salt consumption
so that it remains at a minimum.Your local Water Board can sup-
ply the degree of hardness of the water in your area.
To adjust salt consumption,proceed as follows:
The appliance is equipped with a special softener that uses a
salt specifically designed to eliminate lime and minerals from the
water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel(supplied) into the hole and intro-
duce about 2 kg of salt.It is normal for a small amount of water
to come out of the salt container.
- Carefully screw the cap back on.
- Unscrew the cap from the salt container;
- There is a ring on the container with an arrow on it (see figure to
the side), If necessary, rotate the ring in the anticlockwise
direction from the "-" setting towards the "+" sign,based on the
hardness of the water being used.
It is recommended that adjustments be made in accordance with
the following scheme:
Water Hardness
Salt
The salt container must be filled when the "low salt" indica-
tor light (located on the control panel) comes on.
Autonomy
(cycles/2kg)
Selector
position
çdH
Clarke
degree
consumption
(Grams/cycle)
mmol/l
To prevent the formation of rust,load the salt just before begin-
ning a wash cycle.
0ꢀ14
MꢀNIT
MꢀNT
L
M
L
NUꢀQQ
QRꢀUV
[UV
OM
QM
SM
NQꢀPS
PSꢀTN
[TN
NIUꢀQIQ
QIRꢀUIV
[UIV
=?J?
SM
jba
?H?
QM
OR
.3.
GB
Detergent and Rinse Aidꢀꢀ
Detergent
Rinse Aid
Detergent specifically intended for use with dishwashers must
be used.The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the "Wash Cycle
Table". The detergent dispenser is located on the inside panel
the door.
This product makes dishes sparkle and helps them to dry with-
out spotting.The dispenser is located on the inside panel of the
door and should be filled after every 80 wash cycle (or when the
rinse aid indicator light comes on for those models with this
feature).
Loading the detergent
Loading the Rinse Aid
To open the "A" cover on the dispenser,press the "B" button.The
detergent for the wash cycle should be poured into the "C"
compartment.
To open the dispenser,turn the "C" cap in the anti-clockwise
dierction and then pour in the rinse aid,making sure not to overfill.
The amount of rinse aid used for each cycle can be regulated by
turning the "F" dose adjustor ,located beneath the "C" cap, with
a screwdriver.There are 6 different settings; the normal dosage
setting is 3.
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks in place.
C
Pre-wash
Important
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,the
dosage adjustor should be turned to a higher setting.
If the dishes have white streaks,turn the dosage adjustor to a
lower setting.
A
B
C
Extended wash
F
C
Notice:To facilitate closing the cover, remove any excess
detergent on the edges of the dispenser.
.4.
GB
Loading the Dishwasher
Before placing the dishes in the dishwasher, remove the large
food particle to prevent the filter from becoming clogged,which
results in reduced performance.
Lower Rack
Upper Rack
If the pots and pans have baked-on food that is extremely hard
to remove, we recommend that they be allowed to soak before
they are washed.This will eliminate the need for extra wash
cycles.
Pull out the rack to facilitate loading the dishwasher.
How to Use the Lower Rack
Load for 12 Standard Settings
We recommend that you place the most difficult to clean items
on the lower rack:pots ,lids,serving dishes and bowls,as shown
in the figure on the right.
It is preferable to place serving dishes and lids on the sides of
the racks in order to avoid blocking the rotation of the top spray
arm.
- Pots,serving bowls,etc.must always be placed top down.
- Deep pots should be slanted to allow the water to flow out.
- The silverware basket can be doubled(see Fig.A) so that only
one section may be used when the silverware load is light. This
also makes space for additional pots and pans,and it can also
be placed in the upper rack.
1
2
- Silverware should be placed in the silverware basket with the
handles at the bottom;if the rack has side baskets,the spoons
should be located individually into the appropriate slots.
Especially long utensils should be placed in the horizontal
position at the front of the upper rack.
3
4
Fig.A
Fig.B
How to Use the Upper Rack
The upper rack is designed to hold more delicate and lighter
dishware,such as glasses,coffee and tea cups and saucers,as
well as plates,small bowls and shallow pans(as long as they are
not too dirty).
- Position the dishes and cookware so that they do not get moved
by the spray of water.
The upper rack can be adjusted for height by using the knobs
located on the sides of the rack itself (see Fig.B).
.5.
GB
Turning on the Appliance
Starting a wash cycleꢀ
Setting the Wash Cycle with a Delayed Start Time
After having completed all of the installation steps in the pre-
ceding paragraphs, turn on the water all the way and press the
ON-OFF button (A) located on the control pannel. The "B" indi-
cator light will come on. At this point, the appliance is on but you
must wait a few seconds before programming the setting for the
cycle.
Premise: After selecting the wash cycle as indicated in the para-
graph entitled ,"Setting and Starting a Wash Cycle..."the delay
time can be set.
By pressing the "E" button (see close-up view-'Control panel")
the start of wash cycle can be delayed for between 1 to 12 hours.
Each time the button is pressed,the display (F) will show the
number of hours for the delay period.Choose the amount of
time desired.When the appliance is started with "I" button,a short
acoustic signal will sound and the delay time on the display will
blink ,indicating that the countdown has begun.
Setting and Starting a wash Cycle
Select the desired cycle by pressing the selector button (G). Each
time the button is pressed, one of the"H" cycle indicator lights
will come on in succession. Choose the wash cycle you feel is
most appropriate for the type of dishes that need washing (consult
the wash cycle table contained in this manual, especially when
first using the appliance).
Press the Start/Pause button(I), and after a few seconds a short
acoustic sound will indicate that the wash cycle has begun and
can no longer be changed. If necessary ,read the paragraph
entitled " Cancelling or modifying a cycle while underway..."
After the time has elapsed,the cycle will start.
Cancelling or modifying a cycle while underway ꢀ
Premise : A cycle that is underway can only be modified if it has
only been running for a short time.Otherwise, the detergent may
have already been used,and the appliance mayhave already
drained the wash water. If this is the case,the detergent dis-
penser must be refilled (see the paragraph entitled,"Loading the
Detergent").
NOTE:
During the delay period ,it is preferable not to change any of the
settings.
a) If it is necessary ,all of the settings must be cancelled by press-
ing the ON-OFF button (A) to indicate that all of the settings
have been cancelled.
At this point,all of the steps for"Setting the Wash Cycle with a
delayed Start Time" and "setting and Starting a Wash Cycle"must
be repeated,following the instructions contained in the corre-
sponding sections.
To modify a cycle that is already underway, press the ON-OFF
button (A) ,then all of the settings will be cancelled.
If you forget to load some of the dishesꢀ
b)If the door is opened during the delay period, the indicator will
blink and acoustic signal will sound, and the countdown will stop.
It will begin again when the door is closed .
The wash cycle can be interrupted by pressing the Start/Pause
button.You can then load additional dishes and turn the appli-
ance back on.The cycle will start where it left off.
Wash cycle Program Light
Wash Cycle adjustment Buttons
1/2 load Button
The wash cycle is running and the cycle indicator light (H) for
the cycle will begin to blink.
At the end of the wash cycleꢀ
This button(see "close-up View - Control Panel",letter"C") make
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load.This will allow you to save on
water and eletrical energy. It can be used before setting any of
the wash cycle, except for the intensive cycle ( if included in the
wash cycle table). Please keep in mind that the amount of deter-
gent should also be cut in half.
Six acoustic signal will indicate that the wash cycle has finished
and the cycle indicator light (H) for the cycle will begin to die out.
Turn off the appliance using the ON-OFF button.Turn off the
water supply to the appliance and open the door. Wait a few
minutes before unloading the dishwasher to avoid handling the
dishes and utensils while they are still hot and more susceptible
to breakage. They will also dry better.
.6.
GB
Energy Saving Tips
- Use the right amount of detergent: if you use too much detergent,
the result will not be cleaner dishes,but,rather,a greater nega
tive impact on the enviroment.
- It is important to try and run the dishwasher when it is fully loaded
to save on enery.In order to prevent odours from forming and
food from caking onto the dishes,you can run the soak cycle.
- Choose the right wash cycle: the choice of cycle depends on
the type of dishware, cookware and utensils being washed and
how dirty they are.
- There is no untility in rinsing dishes ,cookware and untensils before
placing them in the dishwasher.
How to Keep Your Dishwasher in Shape
After Every Wash
Moving the Appliance
After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odours are not
trapped inside.
If the appliance must be moved,try to keep it in the vertical
position.If absolutely necessary,it can be positioned on its back.
Remove the Plug
Seals
Before cleaning or performing maintenance, always remove the
plug from the socket.Do not run risks.
One of the factors that cause odours to form in the dishwasher
is food that remains trapped in the seals.Periodic cleaning with
a sponge will prevent this from occuring.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products.Rather, use only a
cloth and warm soapy water.
When You Go on Holiday
When you go on holiday,it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from
the socket ,turn off the water supply and leave the door of the
appliance slightly ajar.This will help the seals last longer and
prevent odours from forming within the appliance.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water and a little white vinegar,or a clean-
ing product made specifically for dishwasher.
.7.
GB
Wash Cycle Table
Cycle Selection
Description of Cycle
Cycle
Detergent Rinse Aid
Information
Pre-wash with cold water
Extended wash at 70ꢀK
Rinse with cold water.
Rinse with hot waterK
Drying.
Very dirty dishes,pots and
pans.(not to be used with
delicate items)
30g
ꢀ
Intensive
Wash
Pre-wash with cold waterK
Extended wash at 50ꢀK
Rinse with cold waterK
Rinse with hot waterK
Drying.
Normally dirty dishes,pots
and pans without dried-on
residue
Pre-wash: 5g
Extended wash:
25g
ꢀ
( 5 )
Normal wash
(IEC-EN50242)
Economic,fast cycle to be
used on not very dirty dishes
right after they are used.No
drying cycle.
Short wash at 40ꢀK
=Cold rinse .
15g
Rapid Wash
Pre-wash of dishes, pots and
pans while waiting for the load
to be complete after the sub-
sequent meal.
Short cold wash to prevent food
residue from drying on the dishes K
Soak
.8.
GB
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must be
cleaned.
The filter efficiently removes food particles from the wash water,
allowing it to be recirculated during the cycle.For this reason ,it
is a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the"A"semi-circular filter
and cup under running water.To remove the filter assembly,pull
on the cup handle in the upward direction. The entire filter as-
sembly (made up of the "A" semicircular filter and the"B" fine
filter)should be cleaned at least once a month.To clean the filter
and the fine filter,use a cleaning brush .Then,reassemble the
filter parts as shown in the figures below and reinsert the entire
assembly in the dishwasher,positioning in its seat and pressing
downward.
Cleaning the Spray Arms
It may happen that food particle become encrusted on the sprayer
arms and block the hole (see "Close up view [interior]",letters C-
F ).Check the sprayer arms periodically and clean them when
needed.
The dishwasher must not be used without the filters.Improper
replacement of the filters may reduce level of the appliance and
damage dishes and utensils.
A
B
Troubleshooting
The Dishes Are Not Clean
It may occur that the dishwasher does not function or does not
function properly.Before calling for assistance,Iet us see what
can be done first:have you forgotten to press one of the buttons
or to perfom an essential operation?
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishwasher Does Not Start
Have you checked whether:
The Dishwasher Does Not Drain
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the ON-OFF swith is on "ON";
- the water supply is turned on.
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
The Dishwasher Does Not Load Water
Have you checked whether:
If,despite all these checks,the dishwasher still does not function
and/or the problem persists,contact the nearest authorised ser-
vice centre and provide them with the following information:
- the nature of the problem;
- the water is turned on and the hose is connected properly;
- the water supply to the house on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the model type number (Mod...)and the serial number (S/N...),
which are indicated on the plate located on the side of the inner
part of the door.
- the filter for the water supply hose is clogged.
Never call on unauthorised technicians and allow the
parts which are not original spare parts to be installed .
.9.
GB
Installation
Positioning the Appliance
Position the appliance in the desired location.The back should
rest against the wall behind it,and the sides,along the adjacent
cabinets or wall.The dishwasher is equipped with water supply
and drain hoses that can be positioned on the right or the left to
facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned,adjust the feet (screw them in
or out) to level the dishwasher.In any case,the appliance should
not be inclined more than 2ꢀ. If the appliance is level,it will help
ensure proper performance.
Fig.1
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4(gas) connec-
tor and make sure that it is fastened tightly in place (see Fig 1).
If the water pipes are new or have not been used for an ex-
tended period of time,let the water run to make sure that the
water is clear and free of impurities.If this precaution is not taken,
there is a risk that the water inlet can get blocked and damage
the appliance.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm,or let it run into the sink,making sure to avoid bending or
crimping it.Use the speical plastic support that comes with the
appliance (see Fig.2).The free end of the hose must be at a
height between 40 and 100 cm and must not be immersed in
water.
Hot Water Connection
The water supply to the appliance can also be connected to the
house's hot water line (centralised system,heating system),as
long as it does not exceed a temperature of 60ꢀ.
In this case,the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.
Fig.2
Anti-Flooding Protection
Attention:
The dishwasher is equipped with a system that stops the supply
of water in the event of a problem with the water supply hose,or
leaks within the unit,in order to prevent damage to your home.If
for any reason the box containing the electrical components hap-
pens to get damaged,remove the plug for the appliance from the
socket immediately.In order to guarantee that the anti-flooding
feature operates properly, the"A" box with water supply hose
must be attached to the water supply tap as shown in Fig .1.No
other type of connection is acceptable.The water supply hose
must not,under any circumstances,be cut,as it contains electri-
cal parts which are live.If the length of the hose is not adequate
to make a proper connection,the hose must be replaced with
one which is long enough.This hose is available upon request
from specialised retailers and service centres.
The special plastic hose support must be solidly fastened to the
wall to prevent the drain hose from moving and allowing water to
spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate
(located on the stainless steel inner door of the appliance) and
that the electrical system is sized for the maximum voltage on
the rating plate,insert the plug into an electrical socket which is
earthed properly (the earthing of the appliance is a safety re-
quirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug,replace the plug ,rather than us-
ing adpators or the like as they could cause overheating and
burns.
.10.
GB
Installation
Diagram
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environ-
ment and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
|