Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
ITEM 95541
REV 14g
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
4.
Do not force the Hand Winch. Use the correct product for your application.
The correct product will do the job better and safer at the rate for which it is
designed. NEVER attempt to exceed the maximum load capacity of the
Hand Winch (900 pounds).
5.
6.
Check for any condition that may negatively affect the Hand Winch’s
operation. If damaged, have the Winch repaired or replaced before using. Do
not use damaged products. Tag damaged products “Do not use” until repaired.
Prior to using the Hand Winch, make sure to read and understand all
instructions and safety warnings as outlined in the service manual(s) for
the object(s) being winched. Make sure the Hand Winch is capable of safely
winching the object. Make sure the point (vehicle bumper, etc.) at which the
Winch is attached is capable of withstanding the weight of the object.
7.
8.
Industrial applications must follow OSHA requirements.
Maintain labels and nameplates on the Hand Winch. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
9.
Use the right product for the job. There are certain applications for which
this product was designed. Do not use small products to do the work of larger
industrial products. Do not use this product for a purpose for which it was not
intended.
10.
11.
Product service must be performed only by qualified service technician.
Service or maintenance performed by unqualified personnel could result in
a risk of injury.
When servicing the Hand Winch, use only identical replacement parts.
Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of personal injury.
12.
Do not allow children to play with this product. Children should not be
allowed in the work area. This product must always be located out of reach of
children.
13.
14.
Do not lift objects vertically. This Hand Winch is designed for horizontal use
only.
Do not use inappropriate attachments to extend the length of the Winch’s
Strap.
15.
16.
Never lift people or hoist loads over people.
Do not apply a load to the Hand Winch when its Strap is fully extended.
Keep at least four full turns of the Strap on the Drum assembly.
Item 95541
For technical questions, please call 1-888-866-5797
PAGE 3
17.
18.
19.
After moving an object with the Hand Winch, secure the object. Do not rely
on the Hand Winch to hold an object for an extended period of time.
Never operate the Hand Winch if its Strap shows any signs of weakening, is
knotted, or kinked.
If loading a boat onto a trailer without keel or side hull rollers, make sure
the trailer is submerged in the water when the boat is loaded by the Hand
Winch. Attempting to drag the boat onto the trailer while on land can cause
Winch failure, boat damage, and possible injury.
20.
Always examine the internal components of the Hand Winch, its Strap and
Hook before each use. Parts of the Winch may be affected by exposure to
chemicals, salts, rust, or excessive wear.
21.
22.
WARNING! Keep hands away from a load bearing Strap and the Winch’s
internal mechanism when operating.
WARNING! If the Hand Winch fails to move a load after exerting pressure
on the Handle, the load may be too heavy for the Winch. If this occurs, release
pressure and immediately discontinue using the Winch.
23.
WARNING! The warnings and cautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
UNPACKING
When unpacking, check to make sure all the parts shown in the Parts List on page 7
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the front cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
To Attach The Handle:
Insert the Handle Assembly (11) onto the Shaft of the Gear Pinion (10). Then
secure the Handle to the Shaft, using the Lock Nut (12). (See Assy. Diagram.)
Item 95541
For technical questions, please call 1-888-866-5797
PAGE 4
To Attach The Hook Plate:
Align the two 3/8” diameter mounting holes in the Hook Plate (18) with the two
mounting holes in the Base (14). Then secure the Hook Plate to the Base using
two Bolts (20), two Washers (19) and two Nuts (17). (See Assy. Diagram.)
OPERATING INSTRUCTIONS
1.
2.
Wear eye protection. Wear ANSI-approved safety impact goggles when
using this product. Also, wear heavy duty work gloves.
WARNING! NEVER attempt to exceed the maximum load capacity of
the Hand Winch (900 pounds). Do not use this Hand Winch if there is any
doubt as to the actual weight of the load being moved.
3.
4.
5.
To pull out the Strap (21), raise the Lever on the Handle Assembly (11). Then,
disengage the Pawl (6) on the Hand Winch by pushing the Pawl down to its
horizontal position. (See Figures A and B.)
Hook the curved portion of the Hook Plate (18) onto a vehicle bumper or other
stable, stationary object capable of supporting the weight of the load to be
winched. (See Figure B.)
Pull out the length of Strap (21) needed to attach the Hook of the Strap to the
load being winched. IMPORTANT: Always leave at least four turns of Strap
on the Drum Assembly (16) of the Hand Winch to prevent pulling the Strap
completely out of the Winch.
6.
Attach the Hook of the Strap (21) securely to the load being winched.
Item 95541
For technical questions, please call 1-888-866-5797
PAGE 5
7.
8.
Lower the Lever on the Handle Assembly (11). Then, engage the Pawl (16) on
the Hand Winch by pulling the Pawl up to its vertical position.
Pull the Handle Assembly (11) clockwise to pull the load to the desired location.
WARNING! NEVER attempt to exceed the maximum load capacity of
the Hand Winch (900 pounds). Do not use this Hand Winch if there is any
doubt as to the actual weight of the load being moved.
9.
After moving the object with the Hand Winch, secure the object. Raise the Lever
on the Handle Assembly (11) and disengage the Pawl (6) on the Hand Winch by
pushing the Pawl down to its horizontal position. Then disconnect the Strap &
Hook (21) from the load. Do not rely on the Hand Winch to hold an object for
an extended period of time.
10.
When finished, always store the Hand Winch in a clean, dry, safe location out of
reach of children and other unauthorized people.
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
CAUTION! Always release a load from the Hand Winch before performing
any inspection, maintenance, or cleaning.
Before each use: Inspect the general condition of the Hand Winch. Check for
damaged or loose parts, and any other condition that may affect this product’s
safe operation. If a problem occurs, have the problem corrected before further
use. Do not use damaged equipment.
3.
4.
The internal Gears of the Hand Winch should be greased at all times.
Periodically, apply an oil lubricant to the Pawl Lever. The Pawl Lever must
be free of grease, dirt, paint, rust, etc., as these conditions will prevent the Lever
from operating properly.
5.
6.
If the Hand Winch has been used in salt water rinse the entire unit
thoroughly with fresh water. Then lubricate all moving parts.
CAUTION! All maintenance, service, and repairs not discussed in this
manual should only be performed by a qualified service technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKS AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Item 95541
For technical questions, please call 1-888-866-5797
PAGE 6
PARTS LIST AND ASSEMBLY DIAGRAM
Plate
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Item 95541
For technical questions, please call 1-888-866-5797
PAGE 7
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free
from defects in materials and workmanship for the period of 90 days from the date of
purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal
activity, improper installation, normal wear and tear, or to lack of maintenance. We
shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
|