Bucket Grease Pump
91793
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
7. Use eye and ear protection. Always wear ANSI approved impact safety
goggles.Wear an ANSI approved dust mask or respirator when working
around metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines.
9. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and, if damaged, have them repaired by an
authorized technician.The handles must be kept clean, dry, and free from oil
and grease at all times.
10. Remove adjusting keys and wrenches. Check that keys and adjusting
wrenches are removed from the tool or machine work surface before plugging
it in.
11. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving
parts; any broken parts or mounting fixtures; and any other condition that may
affect proper operation.Any part that is damaged should be properly repaired
or replaced by a qualified technician.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
available from Harbor FreightTools.
14. Do not operate tool if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
15. Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
16. The grease gun and bulk grease must bestoredoutofreachofchildren.
17. The brass components of this product contain lead, a chemical known to
the State of California to cause birth defects (or other reproductive
harm). (California Health & Safety code 25249.5, et seq.)
Warning:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are fac-
tors which cannot be built into this product, but must be supplied by the opera-
tor.
SKU 91793 Download from Www.SomanuPalsa.cgoem3. All Manuals Search And Download.
Unpacking
When unpacking, check to make sure the following parts are included.
High Pressure Cast Iron Grease Pump
22 lb. Capacity Steel Bucket
Spring Loaded Steel Follower Plate
2 Meter High Pressure Rubber hose
Fitted Steel Extension and Zerk Coupler
If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual.
Assembly
1. Remove all packaging material from the pump and its parts.
2. Thread the Lever Handle (1) into the Handle Bracket (2), and turn it clockwise
until it is tight.
3. Open all 4 Cover Clamps (17), by lifting their handles up from the bottom, and
letting their clamps fall away from the Drum Cover (5). Remove the complete
Drum Cover (5) and Pump (10) assembly, set these aside.
4. Wipe out the Grease Drum (9) with a clean, dry rag to remove any
contaminants that may be present.
5. Fill the Grease Drum (9) with up to 22 lbs. of bulk grease. Be sure to leave at
least 1” from the top of the Grease Drum (9) unfilled, to make room for the
pump and its components.
NOTE: Never put contaminated grease into the Grease Drum (9) as contaminants
may damage the pump or the mechanism the grease is eventually pumped into. If
grease is spilled onto the floor while filling, that grease should be discarded.
6. Place the Drum Cover (5) and Pump (10) assembly back onto the Grease
Drum (9), with the Follower Plate (8) resting on the grease.
7. Push the Drum Cover (5) down onto the top of the Grease Drum (9).This will
compress the Compression Spring (7), and will expel any air that might be
trapped in the grease.
8. Reattach all four Cover Clamps (17), by positioning the clamp over the edge
of the Drum Cover (5), and pressing the lever of the Cover Clamps (17) down
to lock them closed.Your Grease Pump is now ready for operation.
SKU 91793 Download from Www.SomanuPalsa.cgoem4. All Manuals Search And Download.
Steel Extension (14)
Operation
NOTE: This pump is designed for use with
petroleum based grease only. Do not use
this pump for oil or other low-viscosity
fluids, water-based materials, gasoline or
other flammable liquids, or corrosive
compounds. Do not use any materials
which may damage the steel, iron, brass or
nitrile rubber which make up the mecha-
nism of this pump.
NOTE: On first use, you will have to pump
several times until grease has filled the pump mechanism and the rubber hose.
Point the Steel Extension (14) and Coupler (12) into an appropriate waste recep-
tacle while pumping until grease is expelled from the Coupler (12).
WARNING: Never point the Steel Extension and Coupler toward any person or
animal while pumping. Expelled grease under high pressure may cause severe
injury.
NOTE: In the unlikely event that you are unable to get the grease to flow, it is likely
that there is air trapped in the grease which is interfering with the action of the
pump.To remedy this, open the Air Bleeder (16) by turning it counter clockwise a
few turns by hand. Do not remove the Air Bleeder (16) from the pump.With the Air
Bleeder (16) open, pump the handle until grease is expelled from the Air Bleeder
(16). Close the Air Bleeder (16) by turning it by hand clockwise, until hand tight. Do
not overtighten.
1. To operate the pump, attach the Coupler (12) to the grease fitting of the
equipment being serviced. Hold the Coupler (12) in a straight line with the
grease fitting on the machine, and ensure that the Coupler (12) is securely
fastened.
2. Place one foot onto the Foot Rest (11), and pump the Lever Handle (1).
Grease will flow from the pump into the machine being serviced.When the
machine is full, grease will begin to escape from the overflow port on the
machine.When you observe this, stop pumping.
3. To disconnect the Coupler (12), slightly tilt, twist and pull it off the grease
fitting.
Grease Pump with
Drum Cover removed
SKU 91793 Download from Www.SomanuPalsa.cgoem5. All Manuals Search And Download.
Maintenance
1. When not in use, store the Steel Extension (14) in the vertical steel tube
attached to the side of the Grease Drum (9).
2. Protect the Coupler (12) from damage.Wipe it with a clean rag before each
use to prevent contamination of the grease being injected.
3. Store your Grease Pump in a clean dry place. Protect it from temperature
extremes. Do not expose this tool to corrosive environments.
4. If you observe any grease leaking from the Air Bleeder (16), Discharge Outlet
(15), or Coupler (12), check to be sure these parts are tightly installed.
5. Occasionally lubricate the pivot points of the Handle Bracket (2) and
Connecting Link (4) with a medium weight oil.
Parts List
Part #
Description
Lever Handle
Qty.
1
Part #
10
Description
Qty.
1
1
2
3
4
5
6
7
8
9
Pump
Handle Bracket
Pump Head
1
11
Foot Rest
1
1
12
Coupler
1
Connecting Link
Drum Cover
1
13
Rubber Hose
Steel Extension
Discharge Outlet
Air Bleeder
Cover Clamp
1
1
14
1
Lift Handle
1
15
1
Compression Spring
Follower Plate
Grease Drum
1
16
1
1
17
4
1
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
SKU 91793 Download from Www.SomanuPalsa.cgoem6. All Manuals Search And Download.
Assembly Drawing
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIA-
GRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFAC-
TURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF
ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
SKU 91793 Download from Www.SomanuPalsa.cgoem7. All Manuals Search And Download.
|