arbor press
03551
03552
Model
set up and operating instructions
read this material before using this product.
Failure to do so can result in serious injury.
saVe this Manual.
©
®
Copyright 1997 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual revised 10i
11. Maintain tools With care. Keep
tools sharp and clean for better and
safer performance. Follow instructions
for lubricating and changing accessories.
Inspect tool cords periodically and, if
damaged, have them repaired by an
authorized technician. The handles must
be kept clean, dry, and free from oil and
grease at all times.
damaged should be properly repaired
or replaced by a qualified technician. Do
not use the tool if any switch does not
turn on and off properly.
18. guard against electric shocK.
Prevent body contact with grounded
surfaces such as pipes, radiators,
ranges, and refrigerator enclosures.
19. replaceMent parts and
accessories. When servicing, use
only identical replacement parts. Use of
any other parts will void the warranty.
Only use accessories intended for use
with this tool. Approved accessories are
available from Harbor Freight Tools.
12. disconnect poWer. Unplug when
not in use, before servicing, and when
changing accessories.
13. reMoVe adJusting Keys and
Wrenches. Make it a habit to check
that keys and adjusting wrenches are
removed from the tool or machine work
surface before plugging it in.
20. do not operate tool iF under
the inFluence oF alcohol
or drugs. Read warning labels
on prescriptions to determine if your
judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not
operate the tool.
14. aVoid unintentional starting.
Be sure the switch is in the OFF position
when not in use and before plugging in.
Do not carry any tool with your finger on
the trigger, whether it is plugged in or
not.
unpacKing
15. outdoor eXtensions cords.
When the equipment is operated
outdoors, use only extension cords
intended for outside use. See chart
under “Extension Cords" for the proper
AWG rating depending on the length of
the cord(s) being used.
If any parts are missing or broken,
please call Harbor Freight Tools at the number
on the cover of this manual.
part
1
N/A
6
description
Body
Handle Assembly
Plate
Rack
Qty
1
1
1
1
16. stay alert. Watch what you are
doing; use common sense. Do not
operate any tool when you are tired.
10
17. checK daMaged parts. Before
using any tool, any part that appears
damaged should be carefully checked
to determine that it will operate properly
and perform its intended function. Check
for alignment and binding of moving
parts; any broken parts or mounting
fixtures; and any other condition that may
affect proper operation. Any part that is
SKU 03551 03552 For technical questions, please call 1-800-444-3353.
Page 3
arbor press assembly
asseMbly
Mounting the body to your
Workbench
Plate (#6)
Spring Pin (#7)
(not shown)
1. Select a place on your workbench to
mount the Arbor Press.
Body (#1)
2. Purchase hardware to mount your Arbor
Press to your workbench. Bolt length
will be the thickness of your workbench
plus 2-1/2” of length for the Arbor Press
BODY (#1).
Figure 2 -- Installing the Plate
Body (#1)
1. Place the PLATE (#6) onto the Base of
the BODY (#1) as shown in Figure 2.
Insert the SPRING PIN (#7) into the hole
in the BODY.
Mounting Hole
(not shown)
Mounting Hole
Rack Teeth
Rack (#10)
Figure 1 -- Location of Mounting Holes
3. Use the two mounting holes in the BODY
of the Arbor Press as a template as
shown in Figure 1. Mark and Drill holes
in your workbench.
Body (#1)
Cover (#8)
4. Place the BODY over the holes in the
workbench and insert the bolts through
the holes. Thread on the nuts and
tighten.
Figure 3 -- Installing the Rack
2.
Insert the RACK (#10) down through the top
of the BODY as shown in Figure 3. Make
sure the teeth of the RACK are towards the
rear of the BODY as shown in the Figure.
SKU 03551 03552 For technical questions, please call 1-800-444-3353.
Page 4
3.
Unwrap the Handle Assembly and discard
the protective padding.
7.
Your Arbor Press is ready for use.
Handle Assembly
Body (#1)
Figure 4 -- Installing the Handle Assembly
4.
5.
Insert the GEAR (#14) section of the Handle
Assembly into the side of the Arbor Press as
shown in Figure 4. The GEAR will only fit
into the side shown in the Figure.
You may have to rotate the Handle Assembly
slightly to get the teeth of the GEAR to mesh
with the teeth of the RACK.
Rack (#10)
Ring (#5)
Handle Assembly
Figure 5 -- Attaching the Ring
6.
Slide the RING (#5) onto the protruding end
of the GEAR as shown in Figure 5. Tighten
the SCREW (#4) on the RING to secure the
GEAR and Handle Assembly.
SKU 03551 03552 For technical questions, please call 1-800-444-3353.
Page 5
using the arbor press
operation
adjusting the handle assembly
1. Determine if you will need a moderate or
large amount of leverage for the job.
Rack (#10)
Lock Pin (#11)
Shaft (#15)
Shaft (#15)
Plate (#6)
Figure 7 -- Raising the Rack
Figure 6 -- Adjusting the Shaft
1. Raise the RACK (#10) up by turning the
Handle Assembly as shown in Figure 7.
2. Loosen the LOCK PIN (#11) by turning it
as shown in Figure 6. This will allow you
to adjust the length of the SHAFT (#15).
2. Turn the PLATE (#6) until the appropriate
width opening is centered under the
RACK. The appropriate width depends
upon what you are using the press for.
If you do not want an opening beneath
the RACK, rotate the PLATE until one
of the four solid parts of the PLATE is
underneath the RACK.
3. Adjust the length of the SHAFT to
suit your needs. If a large amount of
leverage is needed for your press job,
lock the SHAFT in the extended position.
If a moderate amount of leverage is
needed, position the SHAFT in the
middle of the GEAR.
3. Place the part you need to press onto
the PLATE.
4. Tighten the LOCK PIN to secure the
Handle Assembly.
4. Turn the Handle Assembly to lower the
RACK until the top of the RACK contacts
the press part.
The following Steps show the SHAFT in
the extended position.
5. Place downward pressure on the Handle
Assembly to press the part as needed.
6. Release pressure on the Handle
Assembly and raise the RACK to remove
the part.
SKU 03551 03552 For technical questions, please call 1-800-444-3353.
Page 6
parts list and asseMbly diagraM
part
description Qty
part
7
8
description Qty
part
13
14
15
16
description Qty
1
2
3
4
5
6
Body
Bolt
1
8
6
1
1
1
Spring Pin
Cover
1
1
1
1
1
1
Screw
Gear
1
1
1
2
Nut
9
Washer
Rack
Lock Pin
Pin
Shaft
Handle
Screw
Ring
Plate
10
11
12
SKU 03551 03552 For technical questions, please call 1-800-444-3353.
Page 7
liMited 90 day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and
durability standards, and warrants to the original purchaser that this product is free from defects
in materials and workmanship for the period of 90 days from the date of purchase. This warranty
does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, criminal activity, improper installation, normal wear
and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons
or property, or for incidental, contingent, special or consequential damages arising from the use
of our product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS
ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint must
accompany the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily and
quickly provide you with a replacement. We will return repaired products at our expense, but if
we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 03551 03552 For technical questions, please call 1-800-444-3353.
Page 8
|