OVER 3 months
08977
�
Peek ‘N Play Discovery Dome™
Thank you for choosing this
unique PLAYSKOOL product!
Adult assembly required.
Tool needed: Phillips/
crosshead screwdriver
(not included).
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
��
�
�
�
�
�
��
��
�
�
�
�
�
��
�
�
�
�
��
�
�
�
�
�
�
�
�
�
�
�
�
��
��
�
�
�
�
�
�
��
��
�
�
�
��
���
�
�
�
��
�
��
��
�
�
�
�
�
�
�
�
�
��
�
�
��
��
��
��
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
��
��
�
��
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
��
�
�
��
�
�������
�������
��
��������
���������
������������
Includes fabric dome with rods, left fence panel/door, right fence panel, threshold, left front
support, right front support, left rear base, right rear base, 3 balls, spider teether, phone, monkey
rattle, fish rattle, mailbox shape sorter (2 pieces) with 3 fit-in shapes, 2 links, triangle, circle,
�������������������
�������������
��������������������
���������������������������
���������������������������
square, 12 washer head screws, LET’S PLAY TOGETHER tip card and playmat.
WARNING: Continuous adult supervision required. To avoid injury and to prevent possible strangulation
and entanglement injury: NEVER place dome in crib or playpen. ALWAYS play with dome on the floor. NEVER add
strings or ties to the dome.
CAUTION: This product contains small parts which are necessary for assembly. Prior to and during
assembly of this product, keep small parts out of children’s reach. Small parts pose a choking hazard to
children under 3 years.
tab
slot
�
�
STEP 5a: Insert the fabric dome’s 2 front rods into
the 2 rod holders located on the left and right front
supports.
STEP 8: Insert the tab on the front of the fabric
dome into the slot on the back of the fence
panels as shown.
NOTE:
Left front rod is marked: LF
Right front rod is marked: RF
�� ��
STEP 5b: Turn the unit on its side and secure the 2
front rods to the 2 rod holders by inserting washer
head screws in each screw point.
STEP 9: Attach tube bottom to slot on left front
support. Secure tube to fabric with tabs as shown.
STEP 6a: Connect the right rear base to the left rear base.
STEP 6b: Turn the newly connected rear base over
and secure it by inserting washer head screws in the
screw points .
STEP 10: Attach the shape sorter lid to the shape
sorter mailbox as shown.
PLAY FEATURES:
Place the playmat on the floor.
NOTE:
�
�
Place the dome on the playmat
so that the dome covers the
corners of the playmat.
Your child will love to explore the
STEP 7a: Insert the fabric dome’s 2 back rods into
activities on the playmat, which include:
the 2 rod holders located on the rear base.
• Peek-a-boo crinkly leaf
NOTE:
• Fun-to-touch satin flower
Left back rod is marked: LR
Right back rod is marked: RR
�
��
��
• Pull ribbon “hair” on the monkey
�
�
�
��
�����
�������
�������
������� ���
�����
Please see your LET’S PLAY
TOGETHER tip card (included) for
all kinds of great play activities
and ideas!
���
����������
����������
�����������
����������
����������
���������
�����������
�����������
����������
��
���������
����������
��������
����������
STEP 7b: Lift the rear panel and secure the 2 back rods to
the 2 rod holders by inserting washer head screws in each
screw point.
DECORATIONS, STORAGE AND PORTABILITY:
3. This Playskool product easily folds together for storage
and portability. Simply fold the front and back together
and connect them using the straps as shown. Use the
convenient carry handle for on-the-go play.
1. Hanging toys can be attached to loops on the sides or
at the top as shown. You can also attach other Let’s Play
Together™ products (sold separately) to loops.
2. Spider teether, rattles and the shape sorter mailbox can be
placed in either of the 2 front slots or the inside slot as shown.
4. Put-and-take pocket doubles as a storage pouch for balls.
TO INSTALL BATTERIES:
CAUTION: TO AVOID BATTERY LEAKAGE
Use a Phillips/crosshead
1. Be sure to insert the batteries correctly and always follow the toy and battery
manufacturers’ instructions;
screwdriver to loosen screw in
battery compartment door (screw
remains attached to door). Insert
2 x 1.5V “AA” or R6 size batteries.
Alkaline batteries recommended.
Replace door and tighten screw.
2. Do not mix old and new batteries or alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries;
3. Always remove weak or dead batteries from the product.
IMPORTANT: BATTERY INFORMATION
Please retain this information for future reference. Batteries should be replaced by an adult.
CAUTION:
1. Always follow the instructions carefully. Use only batteries specified and be sure to insert item correctly by matching
the + and – polarity markings.
2. Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.
3. Remove exhausted or dead batteries from the product.
4. Remove batteries if product is not to be played with for a long time.
5. Do not short circuit the supply terminals.
6. Should this product cause, or be affected by, local electrical interference, move it away from other electrical equipment.
Reset (switching off and back on again or removing and re-inserting batteries) if necessary.
7. RECHARGEABLE BATTERIES: Do not mix these with any other types of battery. Always remove from the product before
recharging. Recharge batteries under adult supervision. DO NOT RECHARGE OTHER TYPES OF BATTERIES.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
�������������
© 2006 Hasbro. All Rights Reserved.
TM & ® denote U.S. Trademarks
08977
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
P/N 6575080000
|