Operating Instructions
REFRIGERATOR/FREEZER COMBINATION
Contents
GB
Installation, 2-3
Positioning and connection
Reversible doors
GB
English
Description of the appliance, 4-5
Control panel
Overall view
Start-up and use, 6-7-8-9-10
Starting the appliance
Navigating the display
Chiller system
Evwer Fresh
Using the refrigerator to its full potential
Using the freezer to its full potential
Maintenance and care, 11
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Replacing the light bulb
FF200DP
FF200DX
Precautions and tips, 12
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 13
Guarantee, 14
After Sales Service, 15
Fitting a new plug
Reversible doors
GB
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
If it is necessary to change the direction in which the
doors open, please contact the Technical Assistance
Centre.
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
-
Connect Green and Yellow wire to terminal marked
'E' or or coloured Green and Yellow.
-
-
Connect Brown wire to terminal marked 'L' or
coloured red or brown.
Connect Blue wire to terminal marked 'N' or
coloured Black or Blue.
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse. A 15amp plug must be
protected by a 15amp fuse, either in the plug or adaptor
or at the distribution board.
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC
& 93/68/EEC
3
Description of the
appliance
ON/OFF
Control panel
GB
ALARM RESET
STANDBY (display energy
saving mode)
REFRIGERATOR
temperature adjustment
REFRIGERATOR display
FREEZER display
ALARM
FREEZER
temperature adjustment
SUPER COOL
EVER FRESH
SUPER FREEZE
HOLIDAY
COOL CARE ZONE
I CARE
ON/OFF
FREEZER - and + temperature adjustment
Used to modify the temperature setting of the freezer;
confirmation corresponding to the selected temperature
appears on the display.
The entire product (both the refrigerator and freezer
compartments) may be switched on by pressing this
button. The red LED indicates that the product is switched
off, while the green LED shows that it is operating.
FREEZER display
REFRIGERATOR - and + temperature adjustment
Used to modify the temperature setting of the refrigerator;
confirmation corresponding to the selected temperature
appears on the display.
Shows the set temperature for the freezer compartment.
SUPER COOL
Activates or deactivates the SUPER COOL function (rapid
cooling). The SUPER COOL LED on the keypad lights up
and ‘SC’ appears on the refrigerator display.
REFRIGERATOR display
Shows the set temperature for the refrigerator
compartment.
SUPER FREEZE
Activates or deactivates the SUPER FREEZE function
(rapid freezing). The SUPER FREEZE LED on the keypad
lights up and ‘SF’ appears on the freezer display.
I-CARE
Controls the activation and deactivation of the I-CARE
function (optimal operating temperature at minimal energy
consumption). When this function is activated, the I-CARE
LED on the keypad lights up. Ten minutes after the most
recent user interaction, the display enters its energy saving
mode (see STANDBY function).
HOLIDAY
Activates or deactivates the HOLIDAY function (the HOLIDAY
LED on the keypad lights up), while the temperature values
+12°C and -18°C appear on the displays respectively. Ten
minutes after the most recent user interaction, the display
enters its energy saving mode (see STANDBY function).
ALARM
An alarm situation has been detected in the product (see
Troubleshooting section).
EVER FRESH
Activates or deactivates the Ever Fresh function. When the
LED is illuminated, the vacuum-packing system is
operating; when the LED switches off the operation is
complete and the container airtight. A red LED signals that
a problem has been encountered.
STANDBY (display energy saving mode)
Used to activate the energy saving mode of the display: all
LEDs on the display switch off apart from the ON/OFF
indicator. To exit the energy saving mode, simply press
any button or open the refrigerator door.
COOL CARE ZONE
ALARM RESET
Used to reset any product alarm statuses which have
occurred (freezer temperature or refrigerator door open).
By pressing this button, it is possible to set any of the 4
operating modes relating to the Cool Care Zone: -8°C, -12°C,
-18°C. The operating modes are illustrated by the
corresponding icons. If none of the three icons is lit, the Cool
Care Zone operates as a normal freezer compartment.
4
Overall view
GB
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not
directly represent the appliance purchased. For more complex features, consult the following pages.
LAMP
Removable lidded
(see Maintenance)
shelf with EGG TRAY
•
Removable multipurpose
SHELVES
SHELVES
•
BOTTLE shelf
•
EVER FRESH
FRUIT and
VEGETABLE bin
COOL CARE ZONE
and FREEZER
compartment
•
ICE CARE ice tray
STORAGE
compartment
Levelling FEET
• Varies by number and/or position.
5
Start-up and use
Starting the appliance
When the HOLIDAY function is active the temperature
may not be adjusted, however the appliance adjusts
itself automatically so that the optimal settings for the
situation are used: +12°C for the refrigerator
compartment and -18°C for the freezer compartment.
The activation of this function is indicated by the
HOLIDAY LED lighting up.
GB
! After transportation of the appliance, carefully place it in
an upright position and wait at least 3 hours before
connecting it to the electricity mains, to make sure it
operates as it should.
• Clean the inside of the refrigerator well using warm
water and bicarbonate of soda before placing food
inside it.
To activate and deactivate the functions, simply press
the relevant button; the function status will be signalled
by the corresponding LED on the keypad switching on
or off.
Several of the functions (SUPER COOL, SUPER
FREEZE, I CARE) are incompatible with others
(HOLIDAY,...); remember that there is a pre-established
order of priority which will help you to operate the
product in the best possible way.
•
The appliance comes with a motor protection control
system which makes the compressor start
approximately 8 minutes after being switched on. The
compressor also starts each time the power supply is
cut off whether voluntarily or involuntarily (blackout).
Freezer compartment
The first time the product is switched on, after you have
selected the desired temperature, we recommend the
SUPER FREEZE function is activated in order to cool
the compartment as quickly as possible. Food should
only be placed in the compartment once the SUPER
FREEZE function has finished its cycle.
The temperature inside this compartment may be set
using the COOL CARE ZONE button. The temperature
values that may be selected are -8°C, -12°C, -18°C;
these values are indicated by the icons on the display. If
the COOL CARE ZONE operating mode has not been
activated, the compartment operates as a normal freezer
compartment.
Refrigerator compartment
The first time the product is switched on, after you have
selected the desired temperature, we recommend the
SUPER COOL function is activated in order to cool the
compartment as quickly as possible. Food should only
be placed in the compartment once the SUPER COOL
function has finished its cycle.
Navigating the display
Setting the temperatures:
If the product is switched on, the refrigerator and freezer
compartment displays will indicate the temperature
values set at that moment. To change them, simply press
the - and + buttons corresponding to the compartment for
which you wish to change the set temperature. More
specifically, each time the buttons are pressed, the
temperature increases or decreases and the level of cold
generated inside the compartment is adjusted
accordingly. The temperature values that may be
selected for the refrigerator compartment are +8°C, +7°C,
+6°C, +5°C, +4°C, +3°C and +2°C, while the values that
may be set for the freezer are -18°C, -19°C, -20°C, -21°C,
-22°C, -24°C and -26°C.
When the “I CARE” function is active, the appliance
automatically adjusts the temperatures according to the
conditions inside and outside the refrigerator, in order to
minimise the amount of energy consumed; the activation
of this function is signalled by the I CARE LED on the
keypad lighting up.
6
Chiller system
depend on the initial freshness of the products,
preparation and storage methods, and correct use of the
Ever Fresh function.
GB
No Frost
The electronic cooling
system No Frost is
! The food’s tendency to spoil and use-by date must
always be borne in mind when using the Ever Fresh food
storage system. This method of storing food does not
change any of the characteristics of the food.
! Use only the containers that come with the product to
store food in the Ever Fresh system. Do not use any
other type of container.
characterised by the
presence of aeration cells
on the upper walls of the
refrigerator compartment.
The No Frost system,
thanks to the presence of
a number of aeration cells,
enables the constant
Ever Fresh system
circulation of air inside the compartment, while the
internal temperature of the refrigerator is kept even using
the same compartment ventilation system.
The Ever Fresh system is activated and deactivated by
means of a button on the refrigerator shelf, an external
button on the contro panel and a knob on the cover of
each container.
The No Frost system circulates cold air continuously to
collect humidity and prevent ice and frost formation. The
system maintains an optimal humidity level in the
compartment, preserving the original quality of the food,
preventing the food from sticking together and making
defrosting a thing of the past. Do not block the aeration
cells by placing food or containers in direct contact with
the refrigerating back panel. Close bottles and wrap food
tightly.
Activating and deactivating Ever Fresh
1. Fill the container. Make sure that the food inside
leaves room for the container to be closed properly.
2. Put the lid on the container.
Ever Fresh
3. Close the handles on either
O
A
side of the container and turn the
knob on the lid of the container
all the way to the CLOSE position.
Then turn the knob anticlockwise
to the VACUUM position
Ever Fresh eliminates air from the
containers that are supplied with
the refrigerator. This ensures that
food is preserved for longer
periods of time while preserving
its original appearance, taste and
nutritional characteristics.
(see figure A).
4. Press the button on the shelf
and place the container in the
central position (see figure B).
1
In
With
Food
normal
EVER
5. Lock the container into position
by pulling the button on the shelf
conditions FRESH*
(see figure C).
General cooked dish
Ready-made rice or pasta dish 2 days
2 days
10 days
10 days
2
6. Activate the Ever Fresh function
by pressing the relevant button on
the control panel (the Ever Fresh
indicator light will illuminate). It
takes approximately 1 minute for
the system to suck the air out of
the containers. This stage is
accompanied by a noise that is
caused by the normal operation of
the Ever Fresh function.
Fresh fish
Fresh raw meat
Hard cheese
Raw vegetables
Fresh fruit
Dry biscuits
2-3 days 4-5 days
3 days 9 days
15 days 60 days
5 days 21 days
10 days 21 days
180 days 365 days
Pastries with cream/custard
Other desserts/pastries
2 days
5 days
10 days
20 days
* The above table is indicative and refers to food storage
in the refrigerator at temperatures ranging between 3°C
and 5°C. The length of time food lasts for will, however,
7
7. Once the air suction phase has been completed, the
Ever Fresh LED switches off automatically.
be respected when storing liquids of any kind.
Vacuuming actual liquid from the container may damage
the Ever Fresh pump.
GB
8. Unlock the container from its position by pressing the
button on the shelf.
• Repeated opening of the vacuumed containers may
disturb the storage conditions of the food inside.
• Before using the system, make sure there is no visible
damage on any part of the container.
• The container valve has a built-in security system. If,
after you have created a vacuum, the valve moves
upward within three days, check the lid has been put on
the container properly and/or that the container is intact.
Check the storage status of the food before repeating
the vacuum storage operation. See Activating and
deactivating Ever Fresh.
• The containers were designed to come into direct
contact with food.
• Do not use the containers for any type of cooking (in
the microwave or oven, on an electric plate, over a
flame, etc.).
9. Take it out of the refrigerator and
turn the knob clockwise to the
D
CLOSE position to avoid
accidental opening (see figure A).
The absence of air inside the
container is indicated by the valve
at the bottom (see figure D).
10. To open the container, turn
E
the knob anticlockwise to the
OPEN position (see figure A): this
will allow air to enter the container
and make it easy to open. The
valve will move upwards as air
enters the container (see figure
E).
• Do not put the containers in the freezer.
Vacuum storage
• Pre-packed foods stored using the vacuum system
must still be consumed before the use-by date.
• Repeatedly storing these vacuum-packed foods does
not change their natural tendency to spoil.
• Do not store defrosted foods using the vacuum system
unless they have been cooked already.
• Stored food should be prepared while fresh (chopped,
sliced, peeled, cooked) and should be in perfect
condition.
• Perishable foods stored using the vacuum system
must still be stored inside the refrigerator.
• Cooked foods must be left to cool before being stored
using the vacuum system.
! The lid of the container is provided with a circular
valve. When the valve is low (figure D) there is no air
inside the container. When the valve is high (figure E) air
is present inside the container.
! If, after you have created a vacuum (instructions
1-9), the valve moves upward (see figure E) within three
days, check the lid has been put on the container
properly and/or that the container is intact. Check the
storage status of the food before repeating the vacuum
storage operation.
! If the system does not work as it should or if the pump
remains in operation for greater amount of time than is
normal, the Ever Fresh function is deactivated and the
Ever Fresh LED begins to flash. Malfunction is also
signalled by an alarm buzzer.
Using the refrigerator to its full potential
To exit the alarm status and restore normal operation of
the EVER FRESH function, after checking the status of
the system and the position of the containers, press the
corresponding button on the display to switch off the
Ever Fresh LED. It will now be possible to reactivate the
function. The Ever Fresh function is deactivated when
the refrigerator compartment is OFF.
• Adjust the temperature using the display.
• Press the SUPER COOL button (rapid cooling) to lower
the temperature quickly. For example, when you place
a large number of new food items inside a fridge the
internal temperature will rise slightly. The function
quickly cools the groceries by temporarily reducing
the temperature until it reaches the ideal level.
• Place only cold or lukewarm foods in the compartment,
Using Ever Fresh to its full potential
not hot foods (see Precautions and tips).
• Remember that cooked foods do not last longer than
raw foods.
The following information is a guide on how to get the
best from the Ever Fresh system and the food it stores.
• Do not store liquids in open containers. They will
increase humidity in the refrigerator and cause
condensation to form.
Ever Fresh containers
• Do not clean the lids in a dishwasher.
• The maximum fill level marked on the container must
8
the optimal food freezing temperature. Once this time
has elapsed the LED remains lit constantly: place the
food inside the freezer and close the door. After 24
hours the food will have been frozen properly and the
function will be deactivated automatically (the LED
switches off); the food may now be moved into the
two lower compartments (so that the Cool Care Zone
can be used if necessary) or even left in the Cool
Care Zone compartment, which operates as a normal
storage compartment when the function has not been
activated.
SHELVES: with or without grill.
Due to the special guides the
shelves are removable and the
height is adjustable (see
diagram), allowing easy storage
of large containers and food.
Height can be adjusted without
complete removal of the shelf.
GB
1
2
Using the freezer to its full potential
• Do not re-freeze food that is defrosting or that has already
been defrosted. These foods must be cooked and eaten
(within 24 hours).
• The Cool Care Zone is a special compartment inside
the freezer which allows the user to select any of the 4
different operating modes in accordance with specific
requirements and the type of food stored inside. The
temperature values that may be selected are -8°C, -
12°C, -18°C; these values are indicated by the icons
on the display. The Cool Care Zone is equipped with
controls that may be operated independently from the
other compartments inside the freezer; the Cool Care
Zone may also be deactivated using the display, so
that it can then be used as a normal freezer
• Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted.
• Do not place glass bottles which contain liquids, and which
are corked or hermetically sealed in the freezer because
they could break.
• The maximum quantity of food that may be frozen daily is
indicated on the plate containing the technical properties
located on the bottom left side of the refrigerator compartment
(for example: Kg/24h: 4).
compartment.
•
Adjust the temperature using the display.
•
In order to obtain a greater amount of space in the
freezer compartment, you may remove the bins
(except the lowest bin and the special COOL CARE
ZONE bin, which has an adjustable temperature) and
place the food directly onto the evaporator plates.
• The Cool Care Zone is a compartment that allows
several types of food to be frozen at the most suitable
temperature (fruit, ice cream and alcoholic drinks); the
other two storage compartments (see overall view) are
designed to store frozen foods under normal
conditions.To freeze foods in safely and correctly,
follow the instructions below.
! Do not open the door during freezing.
For a small quantity (less than half of the maximum
amount shown on the data plate):
! If there is a power cut or malfunction, do not open the
freezer door. This will help maintain the temperature inside
the freezer, ensuring that foods are conserved for at least 9
-14 hours.
- if the Cool Care Zone is activated, place the food in
the two storage compartments, making sure that it
does not come into contact with any food that has
already been frozen; press the rapid-freezing SUPER
FREEZE button (the corresponding LED lights up) and
close the door. The function deactivates automatically
after 24 hours or when the inside of the compartment
has reached the optimal temperature (the LED
switches off).
! to avoid blocking the air circulation inside the freezer
compartment, it is advisable not to obstruct the
ventilation holes with food or containers.
- if the Cool Care Zone is not activated the first
compartment may also be used: place the food inside
and repeat the same steps as detailed above.
For a large quantity (more than half of the maximum
amount shown on the data plate):
Deactivate the Cool Care Zone and empty it, hold
down the SUPER FREEZE button for a few seconds
until the corresponding LED begins to flash. After
approximately 24 hours the freezer will have reached
9
ICE CARE tray
GB
The fact that they are situated on the top part of the
freezer drawers ensures greater cleanliness: the ice no
longer comes into contact with the food placed inside
the freezer compartment; furthermore, the dripping of
the water during filling is avoided (a lid to cover up the
hole after filling with water is also provided).
1. Pull out the tray by pushing it up.
Check that the tray is ompletely empty and fill it with
water through the opening provided.
2. Take care not to exceed the level indicated (MAX
WATER LEVEL). Excess water prevents the ice cubes
from dispensing (if this happens, wait for the ice to
melt and empty the tray).
3. Turn the tray 90°: due to the connected compartments
each mould fills with water (see diagram).
4. Close the opening with the lid provided and put the
tray back, placing the top part in the corresponding
housing and allowing it to drop in again.
5. When the ice has formed (minimum time
approximately 8 hours) knock the tray against a hard
surface and wet the outside so that the ice cubes
come loose and take them out through the opening.
MAX
WATER LEVEL
10
Maintenance and care
Switching the appliance off
Replacing the light bulb
GB
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
To replace the light bulb in the refrigerator compartment,
pull out the plug from the electrical socket. Follow the
instructions below.
Access the light bulb by removing the cover as
indicated in the diagram.
Replace it with a similar light bulb within the power
range indicated on the cover (15W or 25W).
1. Press and hold the ON/OFF button for approximately
two seconds, until everything on the display switches
off apart from the red LED corresponding to the ON/
OFF button.
2. pull the plug out of the socket
!
If this procedure is not followed, the alarm may sound.
This alarm does not indicate a malfunction. To restore
normal operation, it is sufficient to hold the ON/OFF
button down for more than two seconds. To disconnect
the appliance, follow points 1 and 2.
Cleaning the appliance
• The external and internal parts, as well as the rubber
seals may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda or
neutral soap. Do not use solvents, abrasive products,
bleach or ammonia.
• The removable accessories may be soaked in warm
water and soap or dishwashing liquid. Rinse and dry
them carefully.
• The back of the appliance may collect dust which can
be removed by delicately using the hose of a vacuum
cleaner set on medium power. The appliance must be
switched off and the plug must be pulled out before
cleaning the appliance.
Avoiding mould and unpleasant odours
• The appliance is manufactured with hygienic materials
which are odour free. In order to maintain an odour free
refrigerator and to prevent the formation of stains, food
must always be covered or sealed properly.
• If you want to switch the appliance off for an extended
period of time, clean the inside and leave the doors
open.
11
Precautions and tips
! The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
Disposal
GB
• Observe local environmental standards when
disposing packaging material for recycling purposes.
• En base a la Norma europea 2002/96/CE de Residuos
de aparatos Eléctricos y Electrónicos (RAEE), los
electrodomésticos viejos no pueden ser arrojados en
los contenedores municipales habituales; tienen que
ser recogidos selectivamente para optimizar la
recuperación y reciclado de los componentes y
materiales que los constituyen, y reducir el impacto
en la salud humana y el medioambiente. El símbolo
del cubo de basura tachado se marca sobre todos
los productos para recordar al consumidor la
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE..
General safety
obligación de separarlos para la recogida selectiva.
El consumidor debe contactar con la autoridad local
o con el vendedor para informarse en relación a la
correcta eleminación de su electrodoméstico viejo.
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
• The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
Respecting and conserving the environment
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Do not touch the appliance with bare feet or with wet or
moist hands and feet.
• Install the appliance in a fresh and well-ventilated
room. Ensure that it is protected from direct sunlight
and do not place it near heat sources.
• Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve
energy.
• Do not touch the internal cooling elements: this could
cause skin abrasions or frost/freezer burns.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• Before cleaning and maintenance, always switch off the
appliance and disconnect it from the electrical supply. It
is not sufficient to set the temperature adjustment knobs
on OFF (appliance off) to eliminate all electrical contact.
• In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
• Do not use any sharp or pointed utensils or electrical
equipment - other than the type recommended by the
manufacturer - inside the frozen food storage
compartments.
• Do not fill the appliance with too much food:
cold air must circulate freely for food to be preserved
properly. If circulation is impeded, the compressor will
work continuously.
• Do not place hot food directly into the refrigerator. The
internal temperature will increase and force the
compressor to work harder and will consume more
energy.
• Defrost the appliance if ice forms (see Maintenance).
A thick layer of ice makes cold transference to food
products more difficult and results in increased
energy consumption.
• Do not put ice cubes taken directly from the freezer into
your mouth.
• Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold air
from escaping (see Maintenance).
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
• Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.
12
Troubleshooting
Malfunctions:
Possible causes / Solutions:
GB
The display is completely switched off. • The plug has not been inserted into the electrical socket, or not far enough
to make contact, or there is no power in the house.
The motor does not start.
• The appliance comes with a motor protection control (see Start-up and use).
The display is on but it is dim.
• Pull out and reverse the plug before putting it back in the socket.
The alarm sounds, the ALARM icon
flashes on the display, “d” appears on
the refrigerator display and the
• The refrigerator door has been open for more than two minutes.
Close the door of the refrigerator.
refrigerator compartment light flashes.
The alarm sounds, the ALARM icon
flashes on the display and “A1”
appears on the freezer display.
• The temperature inside the freezer is too high. The freezer will maintain a
temperature of around 0°C so that the food will not refreeze, so that you
can decide whether to eat it within 24 hours or refreeze it after it has been
cooked. To silence the buzzer, press the ALARM RESET button or one of
the freezer temperature adjustment buttons, or open and close the
refrigerator door. To remove the “A1” message from the display and
restore normal freezer operation, press one of the freezer temperature
adjustment buttons twice or switch the product off and on again.
The alarm sounds, the ALARM icon
flashes on the display and “A2”
appears on the freezer display.
• The temperature of the freezer is dangerously high: the food inside must
not be eaten. To silence the buzzer, press the ALARM RESET button or
one of the freezer temperature adjustment buttons, or open and close the
refrigerator door. To remove the “A2” message from the display and
restore normal freezer operation, press one of the freezer temperature
adjustment buttons twice or switch the product off and on again.
The refrigerator and the freezer do not
cool well.
• The doors do not close properly or the seals are damaged.
• The doors are opened too frequently.
• The temperature that has been set is too high (see Start-up and use).
• The refrigerator or the freezer have been over-filled.
The food inside the refrigerator is
beginning to freeze.
• The temperature that has been set is too low (see Start-up and use).
The motor runs continuously.
• The SUPER FREEZE button has been pressed (rapid freezing): the yellow
SUPER FREEZE light is on or flashing (see Description).
• The door is not closed properly or is continuously opened.
• The outside ambient temperature is very high.
• The thickness of the frost exceeds 2-3 mm (see Maintenance).
The PURE WIND fan does not rotate
The appliance makes a lot of noise.
• The PURE WIND system is only activated automatically when it becomes
necessary to restore perfect operational conditions inside the refrigerator
compartment.
• The appliance has not been installed on a level surface (see Installation).
• The appliance has been installed between cabinets that vibrate and make noise.
• The internal refrigerant makes a slight noise even when the compressor is
off. This is not a defect, it is normal.
Early ending of functions
• Electrical disturbance on the network or brief interruptions of the power supply
A message appears on the display
(e.g. F01)
• The water discharge hole is blocked (see Maintenance).
13
Guarantee
GB
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown
repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because
of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no
cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result
of improper installation.
Replacement of any consumable item or accessory . These include but are not limited to: plugs,
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you
registering your appliance with us and the parts being fitted by one of our authorised engineers. There
will be a charge for our engineer's time. To activate the extra parts warranty on your appliance, simply call
our registration line on 0870 6092094 (ROI 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08709
088 088 (ROI 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service
Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where necessary, to arrange
for an engineer to call. If we cannot resolve the technical problem we will replace your machine or, if you
prefer, give you your money back.
14
After Sales Service
GB
No one is better placed to care for your Hotpoint appliance during the course of its working life than us -
the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08709 066 066
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08709 077 077
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee
you must register your appliance with us.
UK: 0870 6092094
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use
quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure
that the appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.
15
195075923.00
06/2009
GB
16
|