IBM
48X-20X Internal IDE
CD-ROM Drive
User’s Guide
OPTIONS
by IBM
Contents
© Copyright IBM Corp. 2000
iii
iv 48X-20X Internal IDE CD-ROM Drive: User’s Guide
About this book
This manual contains instructions for installing, configuring, and
troubleshooting the IBM® 48X-20X Internal IDE CD-ROM Drive. The manual is
divided into the following parts:
Part 1: Installation and user’s guide
This part contains the product description and expanded installation
instructions in the following languages:
v English
v French
v Spanish
v Italian
v Brazilian Portuguese
v Traditional Chinese
v Simplified Chinese
v Japanese
Part 2: Appendixes
The appendixes contain inofrmation about product specifications, problem
solving, warranties, and help and service. It also contains the product
warranties and notices.
Note: The illustrations in this manual might be slightly different from your
hardware.
Registering your option
Thank you for purchasing OPTIONS by IBM. Please take a few moments to
register your product and provide us with information that will help IBM to
better serve you in the future. Your feedback is valuable to us in developing
products and services that are important to you, as well as in developing better
ways to communicate with you. Register your option on the IBM Web site at
IBM will send you information and updates on your registered product unless
you indicate on the Web site questionnaire that you do not want to receive
further information.
© Copyright IBM Corp. 2000
v
vi 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Safety information
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety
Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette
produktet.
© Copyright IBM Corp. 2000
vii
Antes de instalar este produto, leia as Informações sobre Segurança.
Pred inštaláciou tohto zariadenia si pečítaje Bezpečnostné predpisy.
Antes de instalar este producto lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
viii 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Part 1: Installation and user’s guide
The IBM®48X-20X Internal IDE CD-ROM Drive can read a compact disc (CD)
containing approximately 680 MB1 of information. It is designed for installation
in a personal computer that uses the integrated drive electronics (IDE) or the
enhanced IDE architecture.
The CD-ROM device delivers data up to 48 times the standard CD-ROM
speed, delivering data at up to 7200 KB2 per second. The drive reads compact
discs that meet the ISO-9660 and High-Sierra Group (HSG) standards. It also
reads multiple-session, extended architecture (XA) discs, such as the Kodak
Photo CD.
Product description
In addition to this book, the option package includes:
v 48X-20X Internal IDE CD-ROM Drive
v One “Y” audio cable, one audio cable
v Four mounting screws (M3 x 5 mm, slotted)
v One IDE cable for connecting two IDE devices
v Laser Safety Guide for CD-ROM drives
Contact your place of purchase if an item is missing or damaged. Be sure to
retain your proof of purchase. It might be required to receive warranty service.
You can find information on how to get help, technical support, and warranty
calling for technical support, refer to “Appendix B. Problem solving” on
Before you begin
Determine whether your computer meets the minimum requirements; see
“System requirements” on page 1-2 for details. Read the following information
before you start your installation.
You must complete the following steps to install the drive:
1. Determine which IDE connector to use and the corresponding configuration
setting.
1. MB equals approximately 1 000 000 bytes when referring to storage capacity.
2. KB equals approximately 1024 bytes when referring to data transfer speeds.
© Copyright IBM Corp. 2000
1-1
2. Place or change the configuration jumper on the drive (and possibly make
changes to the configuration jumpers of other devices).
If you do not understand these procedures or are unsure about your ability to
perform all the procedures described, have a qualified computer technician
install the CD-ROM drive for you.
System requirements
Before you begin installing the drive, be sure your computer meets the
following system requirements.
v Minimum microprocessor: 80486
v Minimum RAM: 4 MB
v 5.25-inch diskette drive
v Available IDE connection
v Available internal power connection
v Available drive bay
v One of the following operating systems:
®
– Microsoft Windows® 95
®
– Microsoft Windows 98
– Microsoft® Windows NT® 4.0
– Microsoft Windows 2000 Professional
– Microsoft Windows Millennium Edition (Me)
Handling instructions
To protect your device during installation, observe the following precautions:
v Handle the drive with care. Dropping or jarring the drive can damage the
components inside the drive housing.
v Keep the device in its antistatic bag until you are ready to install the drive in
your computer. Limit your movements. Movement can cause static electricity
buildup.
v Do not force insertion of the power cable. Doing so might damage the
connector or the drive.
1-2 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Front view of the drive
Refer to the illustration to identify parts that might be referred to in the
installation instructions.
«1¬Headphone jack. Plug headphones in here for audio output.
«2¬Volume control. Adjust this dial to control volume.
«3¬CD tray. Use the CD tray to load a CD into the drive.
«4¬Busy indicator. This light comes on when the drive reads a data CD or
plays an audio CD.
«5¬Manual-eject hole. Use this to eject the CD tray if the Eject/Load button is
not operating correctly.
«6¬Eject/Load button. Push this button to open or close the CD tray.
Back view of the drive
Refer to the illustration to identify parts that might be referred to in the
installation instructions.
«1¬Reserved.
«2¬Audio-out connector. This connector is used to connect the CD-ROM drive
to an audio adapter.
«3¬Configuration pins. The jumper placement on these pins determines the
priority of the CD-ROM drive on the IDE bus.
Part 1: Installation and user’s guide 1-3
«4¬IDE connector. This is used to connect the CD-ROM drive to the IDE cable.
«5¬DC power connector. This is used to connect the dc power cord to the
CD-ROM drive.
Installing the drive
Follow these steps to install the CD-ROM drive in your computer.
Step 1. Opening the computer
1. Turn off the computer and all attached devices.
2. Unplug the power cords for the computer and all attached devices.
3. Remove the cover from the computer.
Step 2. Unpacking the drive
1. Before opening the antistatic bag that the drive is packed in, touch it to an
unpainted metal surface for at least two seconds. This will drain the static
electricity from the package and your body.
2. Remove the drive from the antistatic bag. If you must put the drive down,
place the antistatic bag on a flat padded surface, such as a magazine, and
place the drive on the antistatic bag.
Step 3. Selecting the IDE port
Newer computers typically have two IDE ports, each of which can support two
devices. Typically, the IDE port to which your hard disk drive is connected is
the primary IDE port. The other IDE port is the secondary port. The IDE port
and the cable position that you select determine which configuration jumper
setting that you use for the drive.
v If you have two IDE ports, connect the CD-ROM drive to the secondary IDE
port on your system board or IDE adapter. If the CD-ROM drive is the only
device on the secondary IDE port, use the primary configuration setting. If
the CD-ROM drive is the second device on the secondary port, use the
secondary configuration setting.
v If you must attach the CD-ROM drive to the primary IDE port (the same
port as a hard disk drive or other fast device), use the secondary setting for
the CD-ROM drive and the primary setting for the faster device. In some
instances, you might need to change the hard disk drive configuration
setting to master-with-secondary-present when attaching a secondary device
on the same cable. For further information on setting configuration jumpers
on other devices, refer to the documentation that came with your computer
or with the device in question.
v Some non-IBM computers support the cable-select setting, where the
position of the device on the cable determines whether a device is primary
1-4 48X-20X Internal IDE CD-ROM Drive: User’s Guide
or secondary. See the documentation that came with your computer to
determine if your computer supports this setting.
Step 4. Setting the configuration jumper
The illustration shows the primary «1¬setting, the secondary (or slave)
«2¬setting, and the cable-select «3¬setting. Configure the CD-ROM drive by
placing the jumper over the set of pins corresponding to the setting you chose
in Step 3. See “Step 3. Selecting the IDE port” on page 1-4.
v If you are configuring the CD-ROM device as primary, set the jumper to the
master «1¬ device setting. (This is how the drive is set when it is shipped.) If
there is a second device on the IDE port, make sure that device is configured
as secondary.
v If you are configuring the CD-ROM device as secondary, set the jumper to
the secondary «2¬ device setting. Make sure that the other device on the IDE
port is configured as primary (or primary-with-secondary-present).
v If you are configuring the CD-ROM device as cable-select, set the jumper to
the cable-select «3¬ device setting. If there is another device on the IDE port,
make sure that the second device is also configured for cable-select.
Step 5. Mounting the drive in the bay
Attention: Be sure to use the M3 x5 mm mounting screw in the option
package. Using screws that are too long might damage the drive
You can mount the CD-ROM drive horizontally or vertically in the computer. If
you mount the drive vertically, you must secure any CDs you place into the
drive before the drive tray is closed, or the CD-ROM drive will not be able to
read the CD correctly. For further instructions on securing your CDs in a
vertically mounted drive, go to “Loading a CD” on page 1-9.
1. Slide the drive into the bay. Your computer might have specific required
procedures for installing storage devices. Refer to the documentation that
came with your computer for further instructions.
2. Align the drive-bay screw holes with the threaded holes in the drive
housing or mounting bracket; then thread the screws in loosely to check
their positions. Usually two screws are used on each side.
Part 1: Installation and user’s guide 1-5
3. Check to make sure the alignment is correct; then tighten the screws to
secure the drive. Do not overtighten.
Step 6. Attaching the cables to the drive
Connect the cables to the CD-ROM drive as follows.
1. If you have an audio adapter, locate the included audio cables and
determine which cable best fits the CD audio-in port on your audio
adapter. Connect one end of the selected audio cable to the device
audio-out connector «1¬, and the other end of the cable to your audio
adapter CD audio-in port. Save the other cable in case you use a different
audio adapter in the future.
2. Attach a 40-pin IDE cable connector «2¬to the IDE connector on the drive.
Align the cable so that the color-coded edge is closest to the power cable
connector «3¬. Use the IDE cable provided with this option if there is no
cable attached to the IDE port or if there is only one device connector on
the IDE cable.
3. Attach a four-pin power cable «3¬ to the device dc power connector.
Step 7. Completing the hardware installation
1. Be sure that the drive is securely mounted and the connectors are firmly
attached.
2. Be sure that the cables do not interfere with the computer cover and do not
block the power-supply fan blades or air-flow paths.
3. Reinstall the computer cover.
4. Reconnect all devices and check any devices that might have become
disconnected, such as the keyboard, mouse, and monitor.
5. Connect all power cords to electrical outlets.
1-6 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Step 8. Updating your computer configuration
After you have completed the hardware installation, restart your computer.
Usually, the configuration-setup information screen is displayed. If this screen
is not displayed, check your computer documentation for information about
accessing the configuration or setup utility program.
To see the configuration information for most IBM computers, press the F1
button during startup. When you have finished reviewing the information,
save the changes and exit.
Note: Some older computers with one IDE port might not display the
CD-ROM drive information when you review the configuration-setup
information. You still can use the CD-ROM drive in this situation if you
have correctly completed the installation.
Step 9. Installing device drivers
This section contains the instructions for installing device drivers for the
CD-ROM drive, based on the operating system you are using.
Note: User requirements vary; the device driver settings for that operating
system can be customized. If your computer does not work well with
the default settings given in the installation instructions in this section,
on page A-1 for information on customizing your device driver
configuration settings.
Device driver for Windows 95, Windows 98, Windows NT, Windows
2000, and Windows Me
Windows 98 and Windows Me automatically detect the CD-ROM drive and do
not present any installation screens. If the driver installation screens are
displayed after your operating system starts, follow the instructions on the
screen to install the device drivers. Consult the documentation that comes with
your operating system for more information.
Part 1: Installation and user’s guide 1-7
Use and care of the drive
This section includes instructions for the proper care of CDs and the care and
operation of your CD-ROM drive.
Caring for a CD
CDs are high-density media that must be handled with care and kept clean to
insure that they remain readable. These precautions will help to prolong the
life of your CDs.
Attention: Wiping a CD using a circular motion might cause loss of data.
v Handle the CD by the edges or by the center hole. Do not touch the data
surface of the CD.
v To remove dust or fingerprints, wipe the CD from the center to the edge
with a soft, lint-free cloth.
v Do not write on the surface.
v Do not place the CD in direct sunlight.
v Do not use commercial cleaners to clean the CD.
v Do not bend the CD.
Caring for the CD-ROM drive
To protect your CD-ROM drive during operation, observe the following
precautions.
v Remove an CD from the drive before moving the drive.
v Do not insert foreign objects into the drive.
v Do not remove the drive cover or attempt to service the drive.
v Do not operate the drive under any of the following conditions:
– High temperature, high humidity, or direct sunlight
1-8 48X-20X Internal IDE CD-ROM Drive: User’s Guide
– Excessive vibration, sudden shock, or inclined surface
– Excessive dust
Loading a CD
To load a CD into a horizontally mounted CD-ROM drive do the following:
1. Press the Eject/Load button. The tray slides out of the drive.
2. Insert the CD into the loading tray with the label facing up.
3. Close the loading tray by pressing Eject/Load button, or by gently pushing
the tray in.
Attention: Do not force the tray to open; do not insert foreign objects into
the CD tray.
Part 1: Installation and user’s guide 1-9
To load a CD into a vertically mounted CD-ROM drive do the following:
1. Press the Eject/Load button.
2. Look at the illustrations and compare them to your loading tray.
v If your loading tray looks like the left illustration, insert the CD carefully
so that the edges of the CD are underneath the tabs on the loading tray.
These plastic tabs cover the edges of the CD and hold it in place. The
tabs are attached to the tray itself and cannot be moved.
v If your loading tray looks like the right illustration, insert the CD into
the tray, and gently push the movable tab forward to hold the CD in
place.
3. Close the loading tray by pressing the Eject/Load button, or by gently
pushing the tray in.
1-10 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Manually ejecting a CD
If you press the Eject/Load button and the tray does not slide out, turn off the
computer. Straighten a large paper clip to form a tool, as shown in the
illustration below. The straightened end must extend at least 45 mm (1.8 in.).
Insert the extended end into the manual-eject hole on the front of the drive
until the tray opens. Gently pull out the tray until you can remove the CD.
45 mm
1.8 in
Playing an audio CD
To play an audio CD, you must have an audio-CD program installed in your
computer. Windows 98, Windows Me, Windows NT, and Windows 2000
applications include audio CD player programs.
For more information on using your audio playback software, see the
documentation that comes with your operating system or your computer.
Windows 95, Windows 98, Windows NT 4.0, Windows 2000,
or Windows Me
To use the audio utility do the following:
1. Turn on your computer and start your operating system, if you have not
already done so.
2. Insert an audio CD into the CD-ROM drive.
3. The CD begins playing. If the CD does not start playing, or if you have
problems with the audio, check the documentation that comes with your
audio adapter or computer for problem-solving information.
Using a data CD
Data CDs can contain data files, games, or applications.
Windows 95, Windows 98, Windows NT 4.0, Windows 2000,
or Windows Me
To read a data CD do the following:
1. Turn on your computer and start your operating system, if you have not
already done so.
Part 1: Installation and user’s guide 1-11
2. Insert an data CD into the CD-ROM drive. Many program CDs will
automatically start at this point. If the CD does not automatically start, go
on to step 3.
3. Double-click My Computer.
4. Verify that the CD-ROM icon is displayed.
5. Double-click the CD-ROM icon.
6. Verify that you can view files on the CD.
If you are unable to select the CD-ROM icon or view data, see “Appendix B.
information” on page C-1 for service information.
1-12 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Appendix A. Customizing device driver configuration
settings
This section contains information about how to customize and configure device
drivers.
Changing the Windows 98 and Windows Me device-driver
settings
Windows 98 and Windows Me have two device-driver configuration
parameters: Auto Insert Notify and DMA. These are ordinarily setup
automatically by Windows. If you need to set them up, the following
procedures will help.
The Auto Insert Notify parameter enables the computer to start audio CD
software as soon as a CD is inserted into the CD-ROM drive.
The DMA parameter improves computer performance by having the computer
DMA controller handle moving data from the CD to memory, freeing the
computer microprocessor to perform more important tasks. For example,
activating DMA might make movies and games run more smoothly because
the microprocessor will have more time to perform video tasks.
To change these parameter settings from Windows 98 or Windows Me, do the
following steps. (This also pertains to setting Auto Insert Notification for
Windows NT 4.0.)
1. Click Start-->Settings-->Control Panel.
2. Double-click System.
3. Click the Device Manager tab; double-click CD-ROM; select the CD-ROM
driver listed; then click the Properties button.
4. Click the Settings tab.
5. Under Options, click the box next to either Auto Insert Notification or
DMA.
6. Click OK.
Changing the Windows 2000 desktop device driver
To change the Windows 2000 desktop device driver, follow these steps:
1. Click Start-->Settings-->Control Panel.
2. Double-click System.
3. Click the Hardware tab.
4. Click the Device Manager button.
© Copyright IBM Corp. 2000
A-1
5. Click the IDE ATA/ATAPI controller to open the tree.
6. Double-click the device that corresponds to the port of your CD-ROM. It
will either be Primary IDE or Secondary IDE.
7. Click the Advanced Settings tab.
8. Select the Transfer Mode pull-down and select DMA if available.
9. Click OK.
10. Click Close to close the System Properties window. A message displays,
informing you that the system settings have changed.
A-2 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Appendix B. Problem solving
Computer problems can be caused by hardware, software, or user error. Using
the information in this section, you might be able to solve problems yourself or
gather helpful information you can pass on to a service technician. You might
also need to refer to your computer, operating-system, or audio-adapter
publications.
Problem descriptions
Review the following list for any problem descriptions that might fit your
situation.
Your computer or CD-ROM drive does not operate correctly
or the Busy indicator light does not come on.
Take the following actions:
1. Make sure that the CD is inserted with the label side up or facing out if the
drive is installed vertically.
2. Make sure that all devices are properly connected to the computer and the
electrical outlet.
3. Turn off the computer, unplug the cables from the electrical outlets for your
computer and all attached devices, and remove the computer cover.
4. Make sure that all power and IDE cables are securely attached. Disconnect
the IDE cable and check for bent or misaligned pins. If you do not find any
problems, reconnect the cable. Replace the computer cover, and reattach all
cables and power cords. Turn on the computer and attempt to open the CD
tray by pressing the Eject/Load button. If the tray fails to open and the
Busy indicator light does not display, turn off the computer and try
replacing the 4-pin dc power cable.
5. Make sure that the color-coded edge on the IDE cable aligns with pin 1 on
the IDE port and is closest to the power cable on the CD-ROM drive. See
6. Make sure that the IDE cable is connected to the correct IDE port
information.
7. Check the CD-ROM drive and any other device on the IDE cable for the
proper jumper configuration settings. See “Step 4. Setting the configuration
jumper” on page 1-5 for more information.
8. Check to see if the middle connector on the IDE cable is attached to the
IDE port on the system board. If it is, remove the connector and reattach
the cable correctly. The middle port is used only if you are connecting two
devices to the IDE port. If there are two devices on the IDE port, attach the
© Copyright IBM Corp. 2000
B-1
connector at one end of the cable to the IDE port. Attach the CD-ROM
drive or any other slower device to the middle connector, and attach the
other end connector to your hard disk drive or other device. If you are
connecting only one device to an IDE port, attach one end of the cable to
the IDE port and the other end connector to the device; leave the middle
connector open.
You cannot access the CD-ROM drive, or the CD-ROM icon
does not display (Windows 95, Windows 98, Windows NT
4.0, Windows 2000, or Windows Me)
When the CD-ROM drive is installed, a CD-ROM icon appears in theMy
Computerwindow.
To verify that the icon is there do the following:
1. Double-click My Computer.
2. Look for an icon for the CD-ROM drive.
If a CD-ROM icon is not present in the window that displays:
1. Make sure that the drive has been properly installed.
3. Restart your computer.
If the device icon is still not present, check cable connections and configuration
jumper settings on other devices, and resolve any conflicts that might exist.
If a drive icon is still not found after you try the above procedures, continue
with the following steps.
If you are using Windows 95, Windows 98, or Windows Me follow these
instructions:
1. Click Start-->Settings-->Control Panel.
2. Double click System.
3. Click the Device Managertab.
4. At the top of the box, click View Devices by Type.
5. Double-click Hard Disk Controllersto list the available controllers. Make
sure that there are no conflicts with the controller by doing the following:
a. Click to select a controller from the list.
b. Click the Properties button.
c. On the General tab, under Device Status, there is a statement that
indicates whether that controller is working properly. Click OK to
return to the Device Manager tab in the System Properties window.
B-2 48X-20X Internal IDE CD-ROM Drive: User’s Guide
6. Check to see if there is a conflict between devices by doing the following:
a. In the System Properties window, double-click CD-ROM to list the
available devices, and click to select one from the list.
b. Click the Properties button.
c. Under Device Status, there is a statement indicating whether the
CD-ROM device is working properly. If there is a conflict and one or
both of the devices are nonworking, refer to “Appendix C. Help and
7. Click OK in the System Properties window.
8. Shut down and restart the computer.
If you are using Windows NT 4.0, follow these instructions:
1. Click Start --> Settings --> Control Panel.
2. Double-click SCSI Adapters.
3. Click the Device tab.
4. Check to see that neither controller has conflicts by doing the following:
a. Click to select a controller.
b. Click Properties.
c. Click the Card Info tab; under the Device Status section, there is a
statement indicating whether the controller is working properly.
d. Click OK to return to the SCSI Adapter window.
e. Click to select another controller.
f. Click the Card Infotab; under the Device Status section, check the
statement to see whether the controller is working properly.
g. If you have more than two SCSI controllers, use the above steps to
check the device status of the other controller(s).
h. If you discover a conflict and one or more of the controllers is not
working, refer to “Appendix C. Help and service information” on
If you are using Windows 2000, follow these steps:
1. Click Start --> Settings --> Control Panel.
2. Click System.
3. Click Hardware tab.
4. Click the Device Managerbutton.
5. Double-click Hard Disk Controllers to list the available controllers. Look
for yellow circles with an exclamation point to indicate any conflicts. If
conflicts occur, see Appendixes B or C for further instruction.
Appendix B. Problem solving B-3
The CD-ROM drive is not recognized by the operating
system, or drive performance is erratic.
Some computers, such as IBM PS/ValuePoint models 6472, 6482, 6484, 6492,
and 6494, have a compatible mode and a high performance mode for mass storage
devices. Normally, the CD-ROM drive functions better under high performance
mode.
However, if your drive is not functioning properly in that mode, you might
need to use compatible mode.
Check the configuration-setup information for your computer.
1. Access your configuration utility program.
2. Select Devices.
3. Scroll down to the Mass Storage Devices section.
4. Mass Storage Devices contains the entries Primary IDE Mode and
Secondary IDE mode. These entries are used to set the performance mode
of each IDE port. Set the mode to Compatible for the port on which you
installed your CD-ROM drive.
Other IBM and non-IBM computers might have similar settings. Check to see if
your BIOS or configuration-setup utility provides for compatible and high
performancemodes for IDE performance. For these computers, use the compatible
mode for slower IDE devices, such as this CD-ROM drive. Refer to the
documentation that comes with your computer for additional details on
selecting IDE performance modes. Many older computers will not have a
selection of IDE performance modes. If the CD-ROM drive still does not read
the data CD, the CD-ROM drive might be defective.
The CD cannot be read.
Consider the following actions.
v The CD might be defective; try another CD.
v The CD is not ISO-9660 or High Sierra Group (HSG) compatible. Check with
your place of purchase.
The CD does not play sound.
Consider the following actions.
v Check that you are using an audio CD and not a data CD.
page 1-3 if headphones are connected to the front of the drive.
v Adjust the audio-adapter volume control. See the documentation that comes
with your sound adapter and audio-CD player program.
B-4 48X-20X Internal IDE CD-ROM Drive: User’s Guide
v Turn off the computer, unplug the cables from the electrical outlets for your
computer and all attached devices, and remove the computer cover. Check
that the audio-signal cable connects the CD-ROM with the audio adapter.
You receive a common error message.
These are some common error messages and actions to take when they are
displayed.
v CDR-101
The Not ready reading the drivesituation occurs if you try to access the
CD-ROM drive before the drive is ready. The Busy indicator light comes on
when you attempt to access the drive after loading a CD into the CD tray.
Wait until the Busy indicator light turns off before attempting to access the
drive.
Appendix B. Problem solving B-5
v CDR-103
The CD in the CD-ROM drive is not a High Sierra or an ISO 9660 format.
The CD-ROM drive does not support this format.
The connectors on the audio cables provided do not fit the
connector on your audio adapter.
Some audio adapters might require special cable.s See the documentation that
comes with your audio adapter.
You might have to purchase separately an audio cable for the CD-ROM drive.
The audio-out connector on the CD-ROM drive requires a MPC-2 compliant
the audio connector.) If you are using an IBM computer or IBM audio adapter,
assistance.
The front headphone jack does not work (Windows 98,
Windows 2000, and Windows Me).
If the front headphone jack does not work, do the following steps:
1. Right-click on My Computer.
2. Select Properties.
3. Select the Device Manager tab.
4. Open the tree to CD-ROM.
5. Double-click on the device or select it and press the Properties button.
6. Select the Properties tab.
7. Uncheck the “Enable Digital audio for this CD-ROM device” box.
B-6 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Appendix C. Help and service information
This section contains information on how to obtain online and telephone
technical support.
Online technical support
Online technical support is available during the life of your product. Online
assistance can be obtained through the Personal Computing Support Web site
and the IBM Automated Fax System.
Online technical support
IBM Automated Fax System
1-800-426-3395 (U.S. and Canada)
During the warranty period, assistance for replacement or exchange of
defective components is available. In addition, if your IBM option is installed
in an IBM computer, you might be entitled to service at your location. Your
technical support representative can help you determine the best alternative.
Telephone technical support
Installation and configuration support through the HelpCenter will be
withdrawn or made available for a fee, at IBM’s discretion, 90 days after the
option has been withdrawn from marketing. Additional support offerings,
including step-by-step installation assistance, are available for a nominal fee.
To assist the technical support representative, have available as much of the
following information as possible:
v Option name
v Option number
v Proof of purchase
v Computer manufacturer, model, serial number (if IBM), and manual
v Exact wording of the error message (if any)
v Description of the problem
v Hardware and software configuration information for your system
If possible, be at your computer. Your technical support representative might
want to walk you through the problem during the call.
© Copyright IBM Corp. 2000
C-1
For the support telephone number and support hours by country, refer to the
following table or to the enclosed technical support insert. Support phone
numbers are also available by clicking HelpCenter phone list on the IBM
support Web page at
If the number is not provided, contact your IBM reseller or IBM marketing
representative. Response time may vary depending on the number and nature
of the calls received.
Support 24 hours a day, 7 days a week
Canada (Toronto only)
Canada (all other)
416-383-3344
1-800-565-3344
1-800-772-2227
U.S.A. and Puerto Rico
C-2 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Appendix D. Product warranties and notices
Warranty Statements
The warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies
by country. Part 2 is the same for both statements. Be sure to read both the
Part 1 that applies to your country and Part 2.
v Worldwide except Canada, Puerto Rico, Turkey, and United States
IBM Statement of Limited Warranty for United States, Puerto
Rico, and Canada (Part 1 - General Terms)
This Statement of Warranty includes Part 1 - General Terms and Part 2 -
Country-unique Terms.The terms of Part 2 may replace or modify those of Part
1.The warranties provided by IBM in this Statement of Warranty apply only to
Machines you purchase for your use, and not for resale, from IBM or your reseller.
The term ″Machine″ means an IBM machine, its features, conversions, upgrades,
elements, or accessories, or any combination of them. The term ″Machine″ does not
include any software programs, whether pre-loaded with the Machine, installed
subsequently or otherwise. Unless IBM specifies otherwise, the following warranties
apply only in the country where you acquire the Machine. Nothing in this Statement
of Warranty affects any statutory rights of consumers that cannot be waived or limited
by contract. If you have any questions, contact IBM or your reseller.
Machine - 48X-20X CD-ROM Drive
Warranty period* - One (1) year
* Contact your place of purchase for warranty service information. Some IBM Machines are
eligible for on-site warranty service depending on the country where service is performed.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and
workmanship and 2) conforms to IBM’s Official Published Specifications. The
warranty period for a Machine is a specified, fixed period commencing on its
© Copyright IBM Corp. 2000
D-1
Date of Installation. The date on your sales receipt is the Date of Installation,
unless IBM or your reseller informs you otherwise.
During the warranty period IBM or your reseller, if approved by IBM to
provide warranty service, will provide repair and exchange service for the
Machine, without charge, under the type of service designated for the Machine
and will manage and install engineering changes that apply to the Machine.
If a Machine does not function as warranted during the warranty period, and
IBM or your reseller are unable to either 1) make it do so or 2) replace it with
one that is at least functionally equivalent, you may return it to your place of
purchase and your money will be refunded. The replacement may not be new,
but will be in good working order.
Extent of Warranty
The warranty does not cover the repair or exchange of a Machine resulting
from misuse, accident, modification, unsuitable physical or operating
environment, improper maintenance by you, or failure caused by a product for
which IBM is not responsible. The warranty is voided by removal or alteration
of Machine or parts identification labels.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND
REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM JURISDICTION TO JURISDICTION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION
OR LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH
WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Items Not Covered by Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
Unless specified otherwise, IBM provides non-IBM machines WITHOUT
WARRANTIES OF ANY KIND.
Any technical or other support provided for a Machine under warranty, such
as assistance via telephone with “how-to” questions and those regarding
Machine set-up and installation, will be provided WITHOUT WARRANTIES
OF ANY KIND.
D-2 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Warranty Service
To obtain warranty service for the Machine, contact your reseller or IBM. In the
United States, call IBM at 1-800-772-2227. In Canada, call IBM at
1-800-565-3344. (In Toronto, call 416-383-3344.) You may be required to present
proof of purchase.
IBM or your reseller provides certain types of repair and exchange service,
either at your location or at a service center, to keep Machines in, or restore
them to, conformance with their Specifications. IBM or your reseller will
inform you of the available types of service for a Machine based on its country
of installation. IBM may repair the failing Machine or exchange it at its
discretion.
When warranty service involves the exchange of a Machine or part, the item
IBM or your reseller replaces becomes its property and the replacement
becomes yours. You represent that all removed items are genuine and
unaltered. The replacement may not be new, but will be in good working order
and at least functionally equivalent to the item replaced. The replacement
assumes the warranty service status of the replaced item.
Any feature, conversion, or upgrade IBM or your reseller services must be
installed on a Machine which is 1) for certain Machines, the designated,
serial-numbered Machine and 2) at an engineering-change level compatible
with the feature, conversion, or upgrade. Many features, conversions, or
upgrades involve the removal of parts and their return to IBM. A part that
replaces a removed part will assume the warranty service status of the
removed part.
Before IBM or your reseller exchanges a Machine or part, you agree to remove
all features, parts, options, alterations, and attachments not under warranty
service.
You also agree to
1. ensure that the Machine is free of any legal obligations or restrictions that
prevent its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided
a. follow the problem determination, problem analysis, and service request
procedures that IBM or your reseller provides,
b. secure all programs, data, and funds contained in a Machine,
c. provide IBM or your reseller with sufficient, free, and safe access to
your facilities to permit them to fulfill their obligations, and
d. inform IBM or your reseller of changes in a Machine’s location.
Appendix D. Product warranties and notices D-3
IBM is responsible for loss of, or damage to, your Machine while it is 1) in
IBM’s possession or 2) in transit in those cases where IBM is responsible for
the transportation charges.
Neither IBM nor your reseller is responsible for any of your confidential,
proprietary or personal information contained in a Machine which you return
to IBM or your reseller for any reason. You should remove all such information
from the Machine prior to its return.
Production Status
Each IBM Machine is manufactured from new parts, or new and used parts. In
some cases, the Machine may not be new and may have been previously
installed. Regardless of the Machine’s production status, IBM’s appropriate
warranty terms apply.
Limitation of Liability
Circumstances may arise where, because of a default on IBM’s part or other
liability, you are entitled to recover damages from IBM. In each such instance,
regardless of the basis on which you are entitled to claim damages from IBM
(including fundamental breach, negligence, misrepresentation, or other contract
or tort claim), IBM is liable for no more than
1. damages for bodily injury (including death) and damage to real property
and tangible personal property; and
2. the amount of any other actual direct damages, up to the greater of U.S.
$100,000 (or equivalent in local currency) or the charges (if recurring, 12
months’ charges apply) for the Machine that is the subject of the claim.
This limit also applies to IBM’s suppliers and your reseller. It is the
maximum for which IBM, its suppliers, and your reseller are collectively
responsible.
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2)
LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL,
INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC
CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR
SAVINGS), EVEN IF IBM, ITS SUPPLIERS OR YOUR RESELLER IS
INFORMED OF THEIR POSSIBILITY. SOME JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
D-4 48X-20X Internal IDE CD-ROM Drive: User’s Guide
IBM Statement of Warranty Worldwide except Canada,
Puerto Rico, Turkey, United States (Part 1 - General Terms)
This Statement of Warranty includes Part 1 - General Terms and Part 2 -
Country-unique Terms.The terms of Part 2 may replace or modify those of Part
1. The warranties provided by IBM in this Statement of Warranty apply only to
Machines you purchase for your use, and not for resale, from IBM or your reseller.
The term ″Machine″ means an IBM machine, its features, conversions, upgrades,
elements, or accessories, or any combination of them. The term ″Machine″ does not
include any software programs, whether pre-loaded with the Machine, installed
subsequently or otherwise. Unless IBM specifies otherwise, the following warranties
apply only in the country where you acquire the Machine. Nothing in this Statement
of Warranty affects any statutory rights of consumers that cannot be waived or limited
by contract. If you have any questions, contact IBM or your reseller.
Machine - 48X-20X CD-ROM Drive
Warranty period* - One (1) year
* Contact your place of purchase for warranty service information. Some IBM Machines are
eligible for on-site warranty service depending on the country where service is performed.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and
workmanship and 2) conforms to IBM’s Official Published Specifications. The
warranty period for a Machine is a specified, fixed period commencing on its
Date of Installation. The date on your sales receipt is the Date of Installation,
unless IBM or your reseller informs you otherwise.
During the warranty period IBM or your reseller, if approved by IBM to
provide warranty service, will provide repair and exchange service for the
Machine, without charge, under the type of service designated for the Machine
and will manage and install engineering changes that apply to the Machine.
If a Machine does not function as warranted during the warranty period, and
IBM or your reseller are unable to either 1) make it do so or 2) replace it with
one that is at least functionally equivalent, you may return it to your place of
purchase and your money will be refunded. The replacement may not be new,
but will be in good working order.
Extent of Warranty
The warranty does not cover the repair or exchange of a Machine resulting
from misuse, accident, modification, unsuitable physical or operating
environment, improper maintenance by you, or failure caused by a product for
Appendix D. Product warranties and notices D-5
which IBM is not responsible. The warranty is voided by removal or alteration
of Machine or parts identification labels.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND
REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM JURISDICTION TO JURISDICTION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION
OR LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH
WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Items Not Covered by Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
Unless specified otherwise, IBM provides non-IBM machines WITHOUT
WARRANTIES OF ANY KIND.
Any technical or other support provided for a Machine under warranty, such
as assistance via telephone with “how-to” questions and those regarding
Machine set-up and installation, will be provided WITHOUT WARRANTIES
OF ANY KIND.
Warranty Service
To obtain warranty service for the Machine, contact your reseller or IBM. You
may be required to present proof of purchase.
IBM or your reseller provides certain types of repair and exchange service,
either at your location or at a service center, to keep Machines in, or restore
them to, conformance with their Specifications. IBM or your reseller will
inform you of the available types of service for a Machine based on its country
of installation. IBM may repair the failing Machine or exchange it at its
discretion.
When warranty service involves the exchange of a Machine or part, the item
IBM or your reseller replaces becomes its property and the replacement
becomes yours. You represent that all removed items are genuine and
unaltered. The replacement may not be new, but will be in good working order
and at least functionally equivalent to the item replaced. The replacement
assumes the warranty service status of the replaced item.
D-6 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Any feature, conversion, or upgrade IBM or your reseller services must be
installed on a Machine which is 1) for certain Machines, the designated,
serial-numbered Machine and 2) at an engineering-change level compatible
with the feature, conversion, or upgrade. Many features, conversions, or
upgrades involve the removal of parts and their return to IBM. A part that
replaces a removed part will assume the warranty service status of the
removed part.
Before IBM or your reseller exchanges a Machine or part, you agree to remove
all features, parts, options, alterations, and attachments not under warranty
service.
You also agree to
1. ensure that the Machine is free of any legal obligations or restrictions that
prevent its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided
a. follow the problem determination, problem analysis, and service request
procedures that IBM or your reseller provides,
b. secure all programs, data, and funds contained in a Machine,
c. provide IBM or your reseller with sufficient, free, and safe access to
your facilities to permit them to fulfill their obligations, and
d. inform IBM or your reseller of changes in a Machine’s location.
IBM is responsible for loss of, or damage to, your Machine while it is 1) in
IBM’s possession or 2) in transit in those cases where IBM is responsible for
the transportation charges.
Neither IBM nor your reseller is responsible for any of your confidential,
proprietary or personal information contained in a Machine which you return
to IBM or your reseller for any reason. You should remove all such information
from the Machine prior to its return.
Production Status
Each IBM Machine is manufactured from new parts, or new and used parts. In
some cases, the Machine may not be new and may have been previously
installed. Regardless of the Machine’s production status, IBM’s appropriate
warranty terms apply.
Limitation of Liability
Circumstances may arise where, because of a default on IBM’s part or other
liability, you are entitled to recover damages from IBM. In each such instance,
regardless of the basis on which you are entitled to claim damages from IBM
Appendix D. Product warranties and notices D-7
(including fundamental breach, negligence, misrepresentation, or other contract
or tort claim), IBM is liable for no more than
1. damages for bodily injury (including death) and damage to real property
and tangible personal property; and
2. the amount of any other actual direct damages, up to the greater of U.S.
$100,000 (or equivalent in local currency) or the charges (if recurring, 12
months’ charges apply) for the Machine that is the subject of the claim.
This limit also applies to IBM’s suppliers and your reseller. It is the
maximum for which IBM, its suppliers, and your reseller are collectively
responsible.
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2)
LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL,
INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC
CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR
SAVINGS), EVEN IF IBM, ITS SUPPLIERS OR YOUR RESELLER IS
INFORMED OF THEIR POSSIBILITY. SOME JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
Part 2 - Worldwide Country-Unique Terms
ASIA PACIFIC
AUSTRALIA: The IBM Warranty for Machines: The following paragraph is
added to this Section: The warranties specified in this Section are in addition to
any rights you may have under the Trade Practices Act 1974 or other
legislation and are only limited to the extent permitted by the applicable
legislation.
Extent of Warranty: The following replaces the first and second sentences of
this Section: The warranty does not cover the repair or exchange of a Machine
resulting from misuse, accident, modification, unsuitable physical or operating
environment, operation in other than the Specified Operating Environment,
improper maintenance by you, or failure caused by a product for which IBM is
not responsible.
Limitation of Liability: The following is added to this Section: Where IBM is
in breach of a condition or warranty implied by the Trade Practices Act 1974,
IBM’s liability is limited to the repair or replacement of the goods or the
supply of equivalent goods. Where that condition or warranty relates to right
to sell, quiet possession or clear title, or the goods are of a kind ordinarily
D-8 48X-20X Internal IDE CD-ROM Drive: User’s Guide
acquired for personal, domestic or household use or consumption, then none
of the limitations in this paragraph apply.
PEOPLE’S REPUBLIC OF CHINA: Governing Law: The following is added to
this Statement: The laws of the State of New York govern this Statement.
INDIA: Limitation of Liability: The following replaces items 1 and 2 of this
Section:
1. liability for bodily injury (including death) or damage to real property and
tangible personal property will be limited to that caused by IBM’s
negligence;
2. as to any other actual damage arising in any situation involving
nonperformance by IBM pursuant to, or in any way related to the subject
of this Statement of Warranty, IBM’s liability will be limited to the charge
paid by you for the individual Machine that is the subject of the claim.
NEW ZEALAND: The IBM Warranty for Machines: The following paragraph
is added to this Section: The warranties specified in this Section are in addition
to any rights you may have under the Consumer Guarantees Act 1993 or other
legislation which cannot be excluded or limited. The Consumer Guarantees Act
1993 will not apply in respect of any goods which IBM provides, if you require
the goods for the purposes of a business as defined in that Act.
Limitation of Liability: The following is added to this Section: Where
Machines are not acquired for the purposes of a business as defined in the
Consumer Guarantees Act 1993, the limitations in this Section are subject to the
limitations in that Act.
EUROPE, MIDDLE EAST, AFRICA (EMEA)
The following terms apply to all EMEA countries.
The terms of this Statement of Warranty apply to Machines purchased from an
IBM reseller. If you purchased this Machine from IBM, the terms and
conditions of the applicable IBM agreement prevail over this warranty
statement.
Warranty Service
If you purchased an IBM Machine in Austria, Belgium, Denmark, Estonia,
Finland, France, Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland or
United Kingdom, you may obtain warranty service for that Machine in any of
those countries from either (1) an IBM reseller approved to perform warranty
service or (2) from IBM.
Appendix D. Product warranties and notices D-9
If you purchased an IBM Personal Computer Machine in Albania, Armenia,
Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic, Georgia,
Hungary, Kazakhstan, Kirghizia, Federal Republic of Yugoslavia, Former
Yugoslav Republic of Macedonia (FYROM), Moldova, Poland, Romania, Russia,
Slovak Republic, Slovenia, or Ukraine, you may obtain warranty service for
that Machine in any of those countries from either (1) an IBM reseller
approved to perform warranty service or (2) from IBM.
The applicable laws, Country-unique terms and competent court for this
Statement are those of the country in which the warranty service is being
provided. However, the laws of Austria govern this Statement if the warranty
service is provided in Albania, Armenia, Belarus, Bosnia and Herzegovina,
Bulgaria, Croatia, Czech Republic, Federal Republic of Yugoslavia, Georgia,
Hungary, Kazakhstan, Kirghizia, Former Yugoslav Republic of Macedonia
(FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia, and
Ukraine.
The following terms apply to the country specified:
EGYPT: Limitation of Liability: The following replaces item 2 in this Section:
2. as to any other actual direct damages, IBM’s liability will be limited to the
total amount you paid for the Machine that is the subject of the claim.
Applicability of suppliers and resellers (unchanged).
FRANCE: Limitation of Liability: The following replaces the second sentence
of the first paragraph of this Section: In such instances, regardless of the basis
on which you are entitled to claim damages from IBM, IBM is liable for no
more than: (items 1 and 2 unchanged).
GERMANY: The IBM Warranty for Machines: The following replaces the first
sentence of the first paragraph of this Section: The warranty for an IBM
Machine covers the functionality of the Machine for its normal use and the
Machine’s conformity to its Specifications.
The following paragraphs are added to this Section: The minimum warranty
period for Machines is six months.
In case IBM or your reseller are unable to repair an IBM Machine, you can
alternatively ask for a partial refund as far as justified by the reduced value of
the unrepaired Machine or ask for a cancellation of the respective agreement
for such Machine and get your money refunded.
Extent of Warranty: The second paragraph does not apply.
D-10 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Warranty Service: The following is added to this Section: During the warranty
period, transportation for delivery of the failing Machine to IBM will be at
IBM’s expense.
Production Status: The following paragraph replaces this Section: Each
Machine is newly manufactured. It may incorporate in addition to new parts,
re-used parts as well.
Limitation of Liability: The following is added to this Section: The limitations
and exclusions specified in the Statement of Warranty will not apply to
damages caused by IBM with fraud or gross negligence and for express
warranty.
In item 2, replace ″U.S. $100,000″ with ″1.000.000 DEM.″
The following sentence is added to the end of the first paragraph of item 2:
IBM’s liability under this item is limited to the violation of essential contractual
terms in cases of ordinary negligence.
IRELAND: Extent of Warranty: The following is added to this Section: Except
as expressly provided in these terms and conditions, all statutory conditions,
including all warranties implied, but without prejudice to the generality of the
foregoing all warranties implied by the Sale of Goods Act 1893 or the Sale of
Goods and Supply of Services Act 1980 are hereby excluded.
Limitation of Liability: The following replaces items one and two of the first
paragraph of this Section: 1. death or personal injury or physical damage to
your real property solely caused by IBM’s negligence; and 2. the amount of
any other actual direct damages, up to the greater of Irish Pounds 75,000 or
125 percent of the charges (if recurring, the 12 months’ charges apply) for the
Machine that is the subject of the claim or which otherwise gives rise to the
claim.
Applicability of suppliers and resellers (unchanged).
The following paragraph is added at the end of this Section: IBM’s entire
liability and your sole remedy, whether in contract or in tort, in respect of any
default shall be limited to damages.
ITALY: Limitation of Liability: The following replaces the second sentence in
the first paragraph: In each such instance unless otherwise provided by
mandatory law, IBM is liable for no more than: (item 1 unchanged) 2) as to any
other actual damage arising in all situations involving non-performance by
IBM pursuant to, or in any way related to the subject matter of this Statement
of Warranty, IBM’s liability, will be limited to the total amount you paid for the
Machine that is the subject of the claim.
Appendix D. Product warranties and notices D-11
Applicability of suppliers and resellers (unchanged).
The following replaces the second paragraph of this Section: Unless otherwise
provided by mandatory law, IBM and your reseller are not liable for any of the
following: (items 1 and 2 unchanged) 3) indirect damages, even if IBM or your
reseller is informed of their possibility.
SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND:
Limitation of Liability: The following is added to this Section: IBM’s entire
liability to you for actual damages arising in all situations involving
nonperformance by IBM in respect of the subject matter of this Statement of
Warranty will be limited to the charge paid by you for the individual Machine
that is the subject of your claim from IBM.
TURKIYE: Production Status: The following replaces this Section: IBM fulfills
customer orders for IBM Machines as newly manufactured in accordance with
IBM’s production standards.
UNITED KINGDOM: Limitation of Liability: The following replaces items 1
and 2 of the first paragraph of this Section:
1. death or personal injury or physical damage to your real property solely
caused by IBM’s negligence;
2. the amount of any other actual direct damages or loss, up to the greater of
Pounds Sterling 150,000 or 125 percent of the charges (if recurring, the 12
months’ charges apply) for the Machine that is the subject of the claim or
which otherwise gives rise to the claim.
The following item is added to this paragraph: 3. breach of IBM’s obligations
implied by Section 12 of the Sale of Goods Act 1979 or Section 2 of the Supply
of Goods and Services Act 1982.
Applicability of suppliers and resellers (unchanged).
The following is added to the end of this Section: IBM’s entire liability and
your sole remedy, whether in contract or in tort, in respect of any default will
be limited to damages.
NORTH AMERICA
CANADA: Warranty Service: The following is added to this section: To obtain
warranty service from IBM, call 1-800-565-3344. In Toronto, call 416-383-3344.
UNITED STATES OF AMERICA: Warranty Service: The following is added to
this section: To obtain warranty service from IBM, call 1-800-772-2227.
D-12 48X-20X Internal IDE CD-ROM Drive: User’s Guide
Notices
This publication was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this
document in other countries. Consult your local IBM representative for
information on the products and services currently available in your area. Any
reference to an IBM product, program, or service is not intended to state or
imply that only that IBM product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
IBM intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any non-IBM product,
program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
The following paragraph does not apply to the United Kingdom or any
country where such provisions are inconsistent with local law:
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of
express or implied warranties in certain transactions, therefore, this statement
may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
IBM may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments
may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements
Appendix D. Product warranties and notices D-13
will be the same on generally available systems. Furthermore, some
measurements may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their
specific environment.
Trademarks
The following terms are trademarks of the IBM Corporation in the United
States or other countries or both:
IBM
PS/2
HelpCenter
Microsoft, Windows, and Windows NT are trademarks of the Microsoft
Corporation.
Other company, product, and service names may be trademarks or service
marks of others.
D-14 48X-20X Internal IDE CD-ROM Drive: User’s Guide
48X-20X CD-ROM Drive
Federal Communications Commission (FCC) statement
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
v Reorient or relocate the receiving antenna.
v Increase the separation between the equipment and receiver.
v Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
v Consult an IBM authorized dealer or service representative for help.
Properly shielded and grounded cables and connectors must be used in order
to meet FCC emission limits. Proper cables and connectors are available from
IBM authorized dealers. IBM is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or
by unauthorized changes or modifications to this equipment. Unauthorized
changes or modifications could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Responsible party:
International Business Machines Corporation
New Orchard Road
Armonk, NY 10504
Telephone: 1-919-543-2193
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Industry Canada Class B emission compliance statement
Appendix D. Product warranties and notices D-15
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformite a la reglementation d’Industrie Canada
Cet appareil numérique de classe B est conforme à la norme NMB-003 du
Canada.
Deutsche EMV-Direktive (electromagnetische Verträglichkeit)
Dieses Gerät ist berechtigt in Übereinstimmung mit dem deutschen EMVG
vom 9.Nov.92 das EG-Konformitätszeichen zu führen.
Der Aussteller der Konformitätserklärung ist die IBM UK, Greenock.
Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse B.
European Union - emission directive
This product is in conformity with the protection requirements of EU Council
Directive 89/366/ECC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
IBM can not accept responsibility for any failure to satisfy the protection
requirements resulting from a non-recommended modification of the product,
including the fitting of non-IBM option cards.
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to CISPR 22/European Standard
EN 55022. The limits for Class B equipment were derived for typical residential
environments to provide reasonable protection against interference with
licensed communication devices.
Union Européenne - Directive Conformité électromagnétique
Ce produit est conforme aux exigences de protection de la Directive
89/336/EEC du Conseil de l’UE sur le rapprochement des lois des États
membres en matière de compatibilité électromagnétique.
IBM ne peut accepter aucune responsabilité pour le manquement aux exigences
de protection résultant d’une modification non recommandée du produit, y
compris l’installation de cartes autres que les cartes IBM.
Ce produit a été testé et il satisfait les conditions de l’équipement informatique
de Classe B en vertu de CISPR22/Standard européen EN 55022. Les conditions
pour l’équipement de Classe B ont été définies en fonction d’un contexte
D-16 48X-20X Internal IDE CD-ROM Drive: User’s Guide
résidentiel ordinaire afin de fournir une protection raisonnable contre
l’interférence d’appareils de communication autorisés.
Unione Europea - Directiva EMC (Conformidad électromagnética)
Este producto satisface los requisitos de protección del Consejo de la UE,
Directiva 89/336/CEE en lo que a la legislatura de los Estados Miembros sobre
compatibilidad electromagnética se refiere.
IBM no puede aceptar responsabilidad alguna si este producto deja de
satisfacer dichos requisitos de protección como resultado de una modificación
no recomendada del producto, incluyendo el ajuste de tarjetas de opción que
no sean IBM.
Este producto ha sido probado y satisface los límites para Equipos Informáticos
Clase B de conformidad con el Estándar CISPR22 y el Estándar Europeo EN
55022. Los límites para los equipos de Clase B se han establecido para entornos
residenciales típicos a fin de proporcionar una protección razonable contra las
interferencias con dispositivos de comunicación licenciados.
Union Europea - Normativa EMC
Questo prodotto è conforme alle normative di protezione ai sensi della
Direttiva del Consiglio dell’Unione Europea 89/336/CEE sull’armonizzazione
legislativa degli stati membri in materia di compatibilità elettromagnetica.
IBM non accetta responsabilità alcuna per la mancata conformità alle
normative di protezione dovuta a modifiche non consigliate al prodotto,
compresa l’installazione di schede e componenti di marca diversa da IBM.
Le prove effettuate sul presente prodotto hanno accertato che esso rientra nei
limiti stabiliti per le le apparecchiature di informatica Classe B ai sensi del
CISPR 22/Norma Europea EN 55022. I limiti delle apparecchiature della Classe
B sono stati stabiliti al fine di fornire ragionevole protezione da interferenze
mediante dispositivi di comunicazione in concessione in ambienti residenziali
tipici.
Appendix D. Product warranties and notices D-17
Japanese statement of compliance for products less than or equal to 20 A per
phase
D-18 48X-20X Internal IDE CD-ROM Drive: User’s Guide
IBMR
Part Number: 10K3783
Printed in the United States of America
on recycled paper containing 10%
recovered post-consumer fiber.
(1P) P/N: 10K3783
|